Mhouse MhouseKit WS2S, Installation Instructions Manual

Page: 21 / 36

19
Unused jumpers must be placed in the special compartment for
future use (
fig. 35 ).
03. Carry out the recognition phase as described in paragraph 10.3.3
“Recognition of other devices”.
35
10.4 - MEMORISING ALL RADIO TRANSMITTERS
The control unit contains a radio receiver for GTX4 transmitters; the one
included in the package is pre-memorised and ready to use.
There are two ways of memorising a new transmitter:
• Mode 1 : in this “mode” the radio transmitter is used as a whole, i.e. all
the keys carry out a preset command (the transmitter supplied with the
WS2 is memorised using Mode 1). Obviously a radio transmitter in mode
1 can only control one single automation; that is:
• Mode 2 : one of the four commands available can be associated to
each key. If this mode is used appropriately 2 or more different automa-
tions can be controlled, for example:
Obviously, each transmitter is a separate unit, and while some are mem-
orised in mode 1 others can be memorised in mode 2 on the control unit.
The overall memory capacity is 150 units; memorisation in mode 1 takes
up one unit for each transmitter while mode 2 takes up one unit for each
key.
Key T1 “OPEN” command
Key T2 “Pedestrian opening” command
Key T3 “Open only” command
Key T4 “Close only” command
Caution! – As memorisation procedures have a time limit (10 s), it
is important to read the instructions in the next paragraphs before
starting.
10.4.1 - Memorisation mode 1
01. Press key P1 [B] ( fig. 33 ) for at least 3 s. When the LED P1 [A] ( fig.
35 ) switches on release the key.
02. Within 10 s press any one key on the transmitter for at least 3 s to
memorise it. If the memorisation procedure is successful, the “P1”
LED will flash 3 times.
03. If there are other transmitters to be memorised repeat step 2 within
the next 10 s otherwise the memorisation phase will end automati-
cally.
10.4.2 - Memorisation mode 2
With Mode 2 transmitter memorisation each key can be associated with
any one of the commands shown in table 10.
In Mode 2 each key requires a separate memorisation stage.
01. If the transmitter to be memorised is already memorised (such as the
transmitters supplied which are already memorised in mode I) the
transmitter must be deleted following the procedure described in:
“10.4.4 - Deleting a radio transmitter”.
02. Press key P1 [B] ( fig. 35 ) on the control unit the number of times
equal to the required command, according to Table 9 (e.g. 3 times
for the “Only open” command) .
03. Check that LED P1 [A] ( fig. 35 ) flashes quickly for a number of times
equal to the command selected.
04. Within 10 s press the required key on the radio transmitter for at
least 2 s to memorise it. If the memorisation procedure is successful,
the “P1” LED will flash 3 times slowly.
05. If there are other transmitters to be memorised for the same type of
command, repeat step 03 within the next 10 s otherwise the memo-
risation phase will end automatically.
Key T1 “Open only” command automation No. 1
Key T2 “Close only” command automation No. 1
Key T3 “OPEN” command automation No. 2
Key T4 “OPEN” command automation No. 3
34
TABLE 8
Photocell h= 50 cm; activated
when closing
Photocell h= 100 cm;
activated when closing
Photocell h= 100 cm;
activated when opening and
closing
Photocell Jumpers
A
B
C
D
Photocell h= 50 cm; activated
when opening and closing
Photocell on left activated
on opening
F
Photocell on right activated
on opening
E
Photocell
Jumpers