Metos METOS DOMINATOR Plus User Instructions Download Page 8

19.01.2015

Metos Induction range Dominator

8

4.  COOKING HINTS

1.  Before use, ensure hob surface is clean, dry and free of grease. Remove any burnt on food debris.
2.  Familiarise yourself with cooking area and control settings.
3.  Each cooking zone has a power capacity of 5kW.
4.  Each zone is governed by individual energy regulator.
5.  Control setting is from 1 to 10. (1 - lowest setting, 10 - highest).
6.  Boiling, steaming, poaching, stewing, pot roasting, deep and shallow frying can be achieved on the 

hob.

7.  Ferritic cooking vessels must be used.
8.  To boil liquid, follow this procedure:
•  Fill and position pan centrally within cooking zone. 
•  Turn appropriate switch dial to 10.
•  When boiling occurs, reduce setting and continue to cook by simmering.
9.  The lower setting is dependent on amount and density of liquid and also starch content.
10. Skill is required to control simmering and the ability to select a corresponding temperature setting 

will improve with practice.

11.  Any spillage should be cleaned from hob surface as soon as practically possible.
12.  Setting for roasting is from 6 to 8. Higher poer may cause burning of the food.

Failure to clean filter regularly may cause problems that will not be covered by warranty.

The air intake filter MUST ALWAYS be in place during operation.

Wipe glass-ceramic hob clean using a damp cloth and warm, soapy water. For heavy stains, use a 

scraper while cooking zone is still warm. Wipe down with a damp cloth when zone is cool.

4.1.  Chef’s Tips

Always pre-heat oven to desired temperature. 

Use appropriate trays and NEVER overload oven. 

Place food centrally upon the shelves.

Avoid opening oven doors during cooking process.

If removing food from oven, ensure doors are fully open. 

Cooking times are dependant upon the following:

Pre-heat temperature

Food temperature (e.g. frozen, chilled or ambient)

Shelf load / Oven load / Size and weight of food

                                                                                                                                                                                                    

Summary of Contents for METOS DOMINATOR Plus



















Reviews: