Metasys TC-9100 Series Technical Bulletin Download Page 27 | Manualshive

Page: 27 / 90

background image

Technical Bulletin—TC-9100 Universal Controller

27

Working Set Point (WSP)

The working set point of a controller is calculated from the internal set
point of the controller called the Local Set Point (LSP), Input I2 known
as the Remote Set Point (RS), and Input I3 known as the Reference
Variable (RV). When the controller is in STANDBY mode or NIGHT
mode, an additional parameter is used in the calculation, known as the
“Set Point Bias During Standby” (BSB), or the “Set Point Bias
During Night” (BNT). These set point bias values will normally be
negative numbers for heating controllers to reduce the WSP during
standby or night periods, and positive numbers for cooling controllers to
increase the WSP during standby and night periods. The working set
point of a controller is given by the following equations:
In COMFORT mode:

WSP = (LSP + RS)

×

RV

In STANDBY mode:

WSP = (LSP + RS)

×

RV + BSB

In NIGHT mode:

WSP = (LSP + RS)

×

RV + BNT

Note: In OFF mode, the control module is calculated as in NIGHT mode

but the control module will only operate if the OFF mode override
for that control module has

not

been enabled.

The working set point is also shifted when the Winter or Summer
Compensation function is enabled for the controller concerned. Refer to

Summer/Winter Compensation

for further details.

The working set points of programmable modules configured as
controllers can be read by a supervisory system. Refer to

Supervisory

Functions

for further details.

Error Dead Band in PI Controller

The error dead-band in a PI controller is defined by configuration as 1%
or 0.1% of the proportional band. When the control error (PV - WSP) is
less than the error dead-band, as a positive or negative number, the
integral action of the controller is suspended and the integral term is not
changed. This feature prevents unnecessary cycling of the output when
the process variable is very close to the working set point, due to the slow
increase of the integral term over time.

«
...
25
26
27
28
29
...
»

Summary of Contents for TC-9100 Series



























































































Reviews:

No comments

Related manuals for TC-9100 Series

Brand: Radarcan Pages: 40

Brand: Dahua Pages: 58

Brand: Paradox Pages: 2

MicroTech II UV05

Brand: AAF Pages: 50

Brand: Danfoss Pages: 16

Consolidated 2900-40 Series

Brand: Baker Hughes Pages: 80

AQUASNAP 30RA "B"

Brand: Carrier Pages: 36

Freedom Bridge FB3

Brand: Identiv Pages: 2

Brand: Acumen Pages: 6

Brand: PCB Piezotronics Pages: 12

Brand: Skov Pages: 68

8745 MFC Ethernet

Brand: Burkert Pages: 70

Brand: Tempco Pages: 12

Brand: Gliderol Pages: 2

Brand: Mandik Pages: 34

Brand: ICP DAS USA Pages: 8

Brand: VALPES Pages: 28

Brand: VDH Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands