Metabo MS 36-18 LTX BL 40, Original Instructions Manual

Page: 19 / 144

ENGLISH en
19
Cleaning
Clean and suction the machine's ventilation slots. If
necessary, blow out with dry compressed air. After
a longer period and very frequent use, it is
recommended that the inside of the machine is
cleaned by Customer Service.
Sawing chain
Working with a blunt sawing chain causes
premature wear of the sawing chain, the chain
wheel and the guide rail. It can also cause the
sawing chain to break. It is therefore important that
the sawing chain is sharpened in good time.
Sharpening should be carried out by a specialist
workshop.
The sawing chain cutters have the following angles:
cutting angle = 55°, sharpening angle = 30°. A 4.5-
mm round file is required to sharpen the sawing
chain. Use a flay file to file the depth gauge to a
height of 0.64 mm.
Replace the sawing chain if:
- The length of the cutting edges is less than 5 mm.
- There is too much space between the driving links
and the rivets.
- The cutting speed is too slow.
- The cutting speed cannot be increased even after
sharpening the sawing chain multiple times.
For replacement sawing chains, refer to the
Accessories chapter.
Guide rail
Occasionally, some ball bearing grease must be
applied (with a grease gun, not provided) through
the lubrication holes (19) for the deflector star at the
front end of the guide rail.
The lower edge of the guide rail is particularly
susceptible to wear. To avoid one-sided wear of the
guide rail, it should be turned every time the sawing
chain is sharpened. If necessary: Debur the edges
and file the edges flat with a flat file.
You should also take this opportunity to clean the
groove and the oil inlet bores (28) of the guide rail.
Replace the guide rail if
- The groove does not match the height of the
driving links (which must never touch the
underside).
- If the inside of the guide rail is worn and the sawing
chain tends towards one side as a result.
If the guide rail is replaced, the sawing chain must
also be replaced. For replacement guide rails, refer
to the Accessories chapter.
Chain wheel
If the chain wheel (20) shows signs of greater wear
(deep indentations), it must be replaced.
See the chapter on Repairs.
f
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
Fit accessories securely. If the machine is operated
in a holder: secure the machine well. Loss of control
can cause personal injury.
Bio-chainsaw adhesive oil Order no.: 628441000
Chain
(as a replacement) Order no.: 628439000
Guide rail (as a replacement) Order no.:
628437000
Chargers
: ASC 145 DUO, ASC 55, etc.
Battery packs with different capacities. Buy
battery packs only with voltage suitable for your
power tool.
5.5 Ah (LiHD), order no.: 625368000
etc.
5.2 Ah (Li-Ion), order no.: 625028000
etc.
For a complete range of accessories, see
www.metabo.com or the catalogue.
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Only for EU countries: never dispose of
power tools in your household waste!
According to European Directive 2012/19/EU
on Waste from Electric and Electronic Equipment
and implementation in national law, used power
tools must be collected separately and recycled in
an environmentally-friendly manner.
Discharge the battery pack in the power tool before
disposal. Prevent the contacts from short-circuiting
(e.g. by protecting them with adhesive tape).
30°
55° 0,64 mm
4,5 mm
10. Accessories
11. Repairs
12. Environmental Protection