Mercury 40 FourStroke Tiller Handle Operation Maintenance Warranty Installation Manual Download Page 98

Page: 98 / 107

Fuel Hose Connection

FUEL HOSE CONNECTION

The minimum fuel hose inside diameter (ID) is 8 mm (5/16 in.). The fuel hose

connection on this engine model is a snap lock design. Fasten the remote fuel

hose to the fitting with a metal hose clamp or the plastic type hose clamp that is

provided with the outboard.

28526

Flo‑Torq I Propeller Installation

WARNING

Performing service or maintenance without first disconnecting the battery can

cause product damage, personal injury, or death due to fire, explosion,

electrical shock, or unexpected engine starting. Always disconnect the

battery cables from the battery before maintaining, servicing, installing, or

removing engine or drive components.

WARNING

Rotating the propeller shaft may cause the engine to crank over and start. To

prevent this type of accidental engine starting and possible serious injury

caused from being struck by a rotating propeller, always turn the ignition key

or lanyard stop switch to the "OFF" position and remove the spark plug leads

from the spark plugs while servicing.

1. Lubricate the propeller shaft with 2‑4‑C with PTFE.

26902

INSTALLATION

eng

Summary of Contents for 40 FourStroke Tiller Handle












































































































Search results

Summary of Contents for 40 FourStroke Tiller Handle

Reviews:

Mercury 40 FourStroke Tiller Handle, Operation Maintenance Warranty Installation Manual, Page: 98 / 107

Search results

Summary of Contents for 40 FourStroke Tiller Handle

Reviews: