manualshive.com logo in svg

Mercury 40 FourStroke Tiller Handle, Operation Maintenance Warranty Installation Manual, Page: 63 / 107

Share
Download
Mercury 40 FourStroke Tiller Handle Operation Maintenance Warranty Installation Manual Download Page 63

9. Check for a steady stream of water flowing out of the water pump

indicator hole.

28521

IMPORTANT: If no water is coming out of the water pump indicator hole, stop

the engine and check the cooling water intake for obstruction. No obstruction

may indicate a water pump failure or blockage in the cooling system. These

conditions will cause the engine to overheat. Have the outboard checked by

your dealer. Operating the engine while overheated may cause serious engine

damage.

WARMING UP ENGINE

Before beginning operation, allow the engine to warm up at idling speed for

three minutes.

Gear Shifting

IMPORTANT: Observe the following:

•

Never shift the outboard into gear unless the engine speed is at idle.

•

Do not shift the outboard into reverse when the engine is not
running.

•

Your outboard has three gear shift positions to provide operation: forward,

neutral (out of gear), and reverse.

F

N

R

58150

OPERATION

eng

55

  

Summary of Contents for 40 FourStroke Tiller Handle












































































































Reviews:

No comments