manualshive.com logo in svg

Mercury 40 FourStroke Tiller Handle, Operation Maintenance Warranty Installation Manual, Page: 54 / 107

Share
Download
Mercury 40 FourStroke Tiller Handle Operation Maintenance Warranty Installation Manual Download Page 54

2. Engage the tilt support lever by rotating the knob to bring the support

lever upward.

a -

Tilt support lever

b -

Knob

3. Lower the outboard to rest on the tilt support lever.
4. Disengage the tilt support lever by raising the outboard off the support

lever and rotating the lever down. Lower the outboard.

5. Move the tilt lock lever to the lock/run position.

OPERATING ANGLE ADJUSTMENT

The vertical operating angle of your outboard is adjusted by changing the

position of the tilt pin in the five adjustment holes provided. The outboard

should be locked against this tilt pin by setting the tilt lock lever to the lock/run

position. Proper adjustment allows the boat to run stably, achieve optimum

performance, and minimize steering effort.

NOTE: Refer to the following lists when adjusting the operating angle of your

outboard.

The tilt pin should be adjusted so the outboard is positioned to run

perpendicular to the water when the boat is running at full speed. This allows

the boat to be driven parallel to the water.

a

b

28931

FEATURES AND CONTROLS

  

46

eng

Summary of Contents for 40 FourStroke Tiller Handle












































































































Reviews:

No comments