Mercury 40 FourStroke Tiller Handle Operation Maintenance Warranty Installation Manual Download Page 97

Page: 97 / 107

Fastening the Outboard to the Transom

1. Install the outboard so that the antiventilation plate is in‑line or within

25 mm (1 in.) below the bottom of the boat.

a -

Antiventilation plate

b -

25 mm (1 in.)

2. Apply marine sealer to the shanks of the bolts, not the threads.
3. Fasten the outboard with the provided mounting hardware. Tighten the

locknuts to the specified torque.

NOTE: For a more accurate torque, tighten the locknuts rather than turning the

mounting bolts.

a -

Clamp bracket screw

b -

1/2 in. diameter bolt (4)

c -

Flat washer (4)

d -

Locknut (4)

Description

lb‑in.

lb‑ft

Outboard mounting hardware

–

4. Tighten the clamp bracket screws securely.

8045

58157

INSTALLATION

eng

Summary of Contents for 40 FourStroke Tiller Handle












































































































Search results

Summary of Contents for 40 FourStroke Tiller Handle

Reviews:

Mercury 40 FourStroke Tiller Handle, Operation Maintenance Warranty Installation Manual, Page: 97 / 107

Search results

Summary of Contents for 40 FourStroke Tiller Handle

Reviews: