manualshive.com logo in svg

Mercury 40 FourStroke Tiller Handle, Operation Maintenance Warranty Installation Manual, Page: 6 / 107

Share
Download
Mercury 40 FourStroke Tiller Handle Operation Maintenance Warranty Installation Manual Download Page 6

Fuel and Oil

Fuel Recommendations.................................................................................... 37

Low Permeation Fuel Hose Requirement ........................................................ 38

EPA Pressurized Portable Fuel Tank Requirements........................................ 38

Fuel Demand Valve (FDV) Requirement.......................................................... 38

Mercury Marine's Pressurized Portable Fuel Tank........................................... 39

Filling Fuel Tank............................................................................................... 40

Engine Oil Recommendations.......................................................................... 40

Checking and Adding Engine Oil...................................................................... 41

Features and Controls

Warning System ‑ Manual Starting Models...................................................... 43

SmartCraft Product........................................................................................... 44

Manual Tilt System .......................................................................................... 44

Throttle Grip Friction Adjustment ‑ Tiller Handle Models.................................. 48

Steering Friction Adjustment ‑ Tiller Handle Models.........................................48

Trim Tab Adjustment........................................................................................ 49

Operation

Important Daily Inspection Before Each Use ................................................... 50

Prestarting Check List.......................................................................................50

Operating in Freezing Temperatures................................................................ 51

Operating in Saltwater or Polluted Water......................................................... 51

Prestarting Instructions..................................................................................... 51

Engine Break‑in Procedure...............................................................................52

Starting the Engine ‑ Tiller Handle Models....................................................... 52

Gear Shifting .................................................................................................... 55

Stopping the Engine ........................................................................................ 56

Emergency Starting ......................................................................................... 56

  

iv

eng

Summary of Contents for 40 FourStroke Tiller Handle












































































































Reviews:

No comments