manualshive.com logo in svg

Mercury 40 FourStroke Tiller Handle, Operation Maintenance Warranty Installation Manual, Page: 96 / 107

Share
Download
Mercury 40 FourStroke Tiller Handle Operation Maintenance Warranty Installation Manual Download Page 96

Checking Boat Transom Construction

IMPORTANT: Determine the strength of the boat transom. The outboard

mounting locknuts and bolts should be able to hold 75 Nm (55 lb‑ft) of torque

without the boat transom yielding or cracking. If the boat transom yields or

cracks under this torque, the construction of the transom may not be adequate.

The boat transom must be strengthened or the load carrying area increased.

a -

Transom yielding under bolt torque

b -

Transom cracking under bolt torque

When first determining transom strength, use a dial torque wrench. If the bolt or

nut continues to turn without the torque reading on the dial increasing, it is an

indication that the transom is yielding. The load area can be increased by using

a larger washer or a transom reinforcement plate.

NOTE: The inside holes on the transom reinforcement plate are for the lower

transom bolts and the outside holes are for the upper transom bolts.

a -

Large transom washer

b -

Transom reinforcement plate

Description

Part Number

Large transom washer

67‑896392

Transom reinforcement plate

67‑896305

18961

a

b

a

b

20860

INSTALLATION

  

88

eng

Summary of Contents for 40 FourStroke Tiller Handle












































































































Reviews:

No comments