manualshive.com logo in svg

Mercury 40 FourStroke Tiller Handle, Operation Maintenance Warranty Installation Manual, Page: 100 / 107

Share
Download
Mercury 40 FourStroke Tiller Handle Operation Maintenance Warranty Installation Manual Download Page 100

5. Align the flat sides of the propeller nut with the tabs on the propeller nut

retainer. Secure the propeller nut by bending the tabs up and against the

flats on the propeller nut.

a -

Pins

b -

Tabs

6. Install the spark plug leads.

Flo‑Torq Reflex Drive Hub Propeller Installation

!

 WARNING

Performing service or maintenance without first disconnecting the battery can

cause  product  damage,  personal  injury,  or  death  due  to  fire,  explosion,

electrical  shock,  or  unexpected  engine  starting.  Always  disconnect  the

battery  cables  from  the  battery  before  maintaining,  servicing,  installing,  or

removing engine or drive components.

!

 WARNING

Rotating the propeller shaft may cause the engine to crank over and start. To

prevent  this  type  of  accidental  engine  starting  and  possible  serious  injury

caused from being struck by a rotating propeller, always turn the ignition key

or lanyard stop switch to the "OFF" position and remove the spark plug leads

from the spark plugs while servicing.

Lubricate the propeller shaft splines with 2‑4‑C with PTFE.

12733

a

b

a

b

26906

INSTALLATION

  

92

eng

Summary of Contents for 40 FourStroke Tiller Handle












































































































Reviews:

No comments