manualshive.com logo in svg

Mercury 40 FourStroke Tiller Handle, Operation Maintenance Warranty Installation Manual, Page: 7 / 107

Share
Download
Mercury 40 FourStroke Tiller Handle Operation Maintenance Warranty Installation Manual Download Page 7

Maintenance

Outboard Care.................................................................................................. 58

EPA Emissions Regulations............................................................................. 58

Inspection and Maintenance Schedule............................................................. 59

Flushing the Cooling System............................................................................ 60

Top Cowl Removal and Installation.................................................................. 62

Exterior Care.....................................................................................................62

Battery Inspection ............................................................................................ 62

Fuel System...................................................................................................... 63

Engine Fuel Filter ‑ Manual Starting Models.....................................................63

Corrosion Control Anode.................................................................................. 64

Propeller Replacement..................................................................................... 65

Spark Plug Inspection and Replacement..........................................................68

Timing Belt Inspection...................................................................................... 69

Lubrication Points............................................................................................. 70

Changing Engine Oil ........................................................................................ 72

Gearcase Lubrication........................................................................................73

Gearcase Lubricant Recommendation............................................................. 75

Submerged Outboard....................................................................................... 75

Storage

Storage Preparation..........................................................................................76

Protecting External Outboard Components...................................................... 76

Protecting Internal Engine Components........................................................... 76

Gearcase.......................................................................................................... 77

Positioning Outboard for Storage..................................................................... 77

Battery Storage................................................................................................. 77

Troubleshooting

Engine Will Not Start.........................................................................................78

Engine Runs Erratically.................................................................................... 78

Performance Loss.............................................................................................78

Battery Will Not Hold Charge............................................................................ 79

Owner Service Assistance

Parts and Accessories Inquiries....................................................................... 80

Service Assistance........................................................................................... 80

Ordering Literature............................................................................................82

eng

v

  

Summary of Contents for 40 FourStroke Tiller Handle












































































































Reviews:

No comments