background image

P 10

Please retain product label and instructions for future reference

             

Rubber Mallet 

may be required 

to fit parts.

IMPORTANT: 

Pre-drill before fixing screws.

Pre drill 

hole

Step 17

Parts needed - No. 37 QTY 3

 

Align the Roof Purlins (

No.37

into the cut out slots on each gable top 

ensuring each ridge bar interlocks the 

boards.

 

Secure the ridge bars at each 

end by screwing through the purlins 

into the boards (

ensure to pre-drill to 

avoid the boards splitting

) using 

4x70mm screws per roof purlin.

*Please note:

 The gable shown is for 

illustrative purposes and may differ in 

width from your choice in product. 

Nevertheless, despite any differences the 

process of fixing the roof purlin is the 

same.

12x70mm Screws

70mm 

screw

37

37

37

37

a

b

a

32

b

33

23b

33

33

Step 18

Parts needed - No. 33 QTY 74

 

Place the first two roof board’s 

(No.33) 

onto either side of the log cabin, 

making sure the boards are fush to the 

end of the roof purlin. Once in position fix 

to each purlin using 3x40mm screws.

*Ensure the roof boards meet at the top 

of the apex and leave an overhang at the 

bottom.

Continue adding the roof boards along 

the roof, fixing each one into position 

using 3x40mm screws, making sure that 

each board is interlocked, flush at the 

bottom & meet at the top of the apex.

Ensure the roof boards are not laid too 

close together, use the spacers

 (No. 44)

 

provided to create a 2mm gap. Adjusting 

the spacing between the boards allows 

the wood to swell in damp weather.

You have been issued with 74 roof boards, 

but in reality you may only need to use 72.

 

The last board on each side will 

overhang past the end of the roof purlin; 

Using a straight edge and a pencil mark 

out a line as a guide. 

Cut along the pencil mark and remove the 

excess. Place the cut down board’s back 

onto the roof and secure into place using 

3x40mm screws per board.

*Please Note: 

This image is for illustrative 

purposes and may differ from your choice in 

product. Nevertheless the process of cutting 

and fitting the last roof board(s) is the same.

222x40mm Screws 

40mm 

screw

Pre drill 

hole

*

Cut to fit

a

b

IMPORTANT : 

Pre-drill before fixing screws.

Summary of Contents for 0628RANE0403HGDD2SW-V1

















Reviews: