background image

User Manual FSK700-2 / FSK700-2SX

Chapter 1   •  Introduction

7

1.3 

Types of signs

Especially important passages in this manual are marked with signs. The following signs are used:

ATTENTION! Disregard of this reference can lead to malfunction or damage to the unit.

TIP!

 This passage contains notes that will help ease operation.

The country-specific and/or the site-specific requirements of the device and/or system 

APPROVALS

 must be observed.

1.4 

Outline of the manual

Following the 

safety instructions

 on page 4, and guidelines given in the 

first chapter

, which 

should be implicitly observed,

chapter two

 contains all information required to 

operate

 a Series FSK700 Fire Brigade Key 

Safe. It is explained how the Fire Brigade Key Safe works in combination with a fire detection 
control panel, a controlling and monitoring device, an unblocking device, and a transmitting 
device, as well as describing in which situations sabotage alarm is activated.

In 

chapter three

, relevant guidelines for the 

installation

 of the Fire Brigade Key Safe by a spe-

cialist installer are given.

In 

chapter four

, the specialist installer is provided with an overview of the arrangement of ter-

minals, connectors, and other important elements, as well as information required to 

connect 

the Fire Brigade Key Safe to an MEP Key Safe Controlling and Monitoring Device AD900-1, 
and to a fire detection control panel.

In 

chapter five

commissioning

 of the Fire Brigade Key Safe is described in detail for the spe-

cialist installer.

In 

chapter six

, notes on 

inspection

 and 

maintenance

 of the unit are given. Also described in 

this chapter are possible causes of 

malfunction

 and steps to correct them.

In 

chapter seven

, all essential 

technical specifications

 of the unit are presented.

In 

chapter eight

, copies of the 

VdS-Prüfzertifikat

 and the 

EC Declaration of Conformity

 are 

provided.

1.5 

Abbreviations

The correct designations for both Key Safe types "Fire Brigade Key Safe FSK700-2" and "Fire Bri-
gade Key Safe FSK700-2SX" are shortened to "Fire Brigade Key Safe", "Key Safe", or "Series 
FSK700" for improved readability of the manual. Differences between the two types are noted in 
the respective text passages.

1.6 

Important advice for the operator and specialist installer

The keeping of keys in a Fire Brigade Key Safe results in an increased level of danger, which the 
insurance company must be informed of.

If the key depot is not VdS-certified and/or is not installed, operated and maintained 
according to the VdS-Richtlinien für Schlüsseldepots, Planung, Einbau und Instandhaltung 
(VdS 2350), it is possible that no insurance protection is available for damages due to burg-
lary, in case the building has been opened using the (real) key taken from the key depot.

The Fire Brigade Key Safe must only be used in combination with components recommended or 
certified by the manufacturer, and exclusively for the application described in the manual.

HB_FSK700_1020_9161690_Englisch_D.odt / 1022 D / AN9161690
ZN62163/38/7

7

Summary of Contents for Fire Brigade Key FSK700 Series







































Reviews: