background image

6

Chapter 1   •  Introduction

User Manual FSK700-2 / FSK700-2SX

Fig. 2:

Series FSK700 Fire Brigade Key Safe

On the left: FSK700-2 with open outer and inner doors, master key inserted, inner door fitted  

with a double-bit variable lock

On the right: FSK700-2SX with 4 master keys, open outer and inner doors, inner door fitted with  

a lock for a locking half cylinder

1.2.1 

Main features of the Series FSK700 Key Safe

The Series FSK700 Key Safe has been 

tested

 and 

certified

 (Certification No. 

G 199055

) by 

VdS 

Schadenverhütung

 GmbH (VdS). In combination with a VdS-certified Key Safe controlling and 

monitoring device, it can be employed together with most commercially available 12V or 24V fire 
detection and burglar alarm systems.

The Series FSK700 Key Safe conforms to 

DIN 14675 Appendix C – Class 3 

(FSD 3, high risk).

Up to 

four master keys

 can be stored inside a Fire Brigade Key Safe, thus meeting even complex 

organisational requirements.

Due to 

intelligent details in design

 – for instance, protected outer door hinges – high security 

against unauthorised opening is achieved.

The self-adjusting magnetic closure device automatically assumes the optimal position – therefore, 
the 

closure device

 is able to function at the 

highest precision level

, even during 

long-time opera-

tion

 under unfavourable temperatures or environmental conditions

.

To guarantee high 

corrosion resistance

 and 

mechanical stability

, all vital mechanical parts are 

made from stainless steel.

Installation

 of the Key Safe is 

easy and smooth

 due to the Flush Mounting Frame introduced 

many years ago in Germany by MEP.

An 

acoustic warning signal

 will sound from the Key Safe if not all master keys have been inserted 

correctly.

For application of 

different locking mechanisms

, such as double-bit variable locks or locking half 

cylinders, suitable 

inner doors

 are available.

To assure unhindered opening of the Key Safe at 

low outside temperatures

, the outer door can be 

electrically heated with 12V or 24V AC or DC. 

Heating is controlled by temperature

, operating 

only at temperatures below +10°C (at factory default settings).

Adaption

 of the magnetic closure device and heating device to different voltages (12V or 24V) is 

performed 

automatically

 by all Series FSK700 units, guaranteeing quick and problem-free com-

missioning.

HB_FSK700_1020_9161690_Englisch_D.odt / 1022 D / AN9161690

ZN62163/38/6

6

Summary of Contents for Fire Brigade Key FSK700 Series







































Reviews: