background image

User Manual FSK700-2 / FSK700-2SX

Chapter 4   •  Connection

25

1)

See page 25 and onwards in chapter 4.5.3: "Connecting the cables of the Locking Cylinder Mounting
Brackets"
 

Fig. 15:

Connecting the closure device, ribbon cable of the outer door, and cables of the Locking Cylin-
der Mounting Brackets to Connection Board APL-4. Example pictures Key Safe FSK700-2SX,  
upgraded to keep 4 master keys.

4.5.1 

Ribbon cable of the outer door

Following connecting the terminals, connect the ribbon cable of the outer door to connector ST7 on 
Connection Board APL-4. Place the ribbon cable inside the Key Safe in a way that operating the 
locking half cylinder(s) does not damage the cable.

4.5.2 

Cable of the closure device

Connect the cable of the closure device to connector ST6 on Connection Board APL-4. Ensure that 
the two red connecting wires are on the bottom side (see Fig. 15 above).

Adaption of the closure device to the voltage of the fire detection control panel (12VDC or 
24VDC) is performed automatically.

Should the cable of the closure device not be properly connected to connector ST6 on Connec-
tion Board APL-4, the closure device cannot function properly – as a result, the outer door of the 
Key Safe cannot be opened anymore.

Should the cable of the closure device be connected to connector ST6 with wrong polarity, 
this can lead to the Connection Board APL-4 becoming defective!

 

4.5.3 

Connecting the cables of the Locking Cylinder Mounting Brackets

1)

Install positions for the Locking Cylinder Mounting Bracket are pictured in Fig. 9 on page 18.

Fig. 16:

Connecting positions of the Locking Cylinder Mounting Brackets on Connection Board APL-4 
throughout the upgrade stages of the Series FSK700 Key Safe

The cable leading from the Locking Cylinder Mounting Bracket in Key Safe FSK700-2 is the 
only cable to be connected to connector ST1 on Connection Board APL-4! When using Key Safe 
FSK700-2SX, it is imperative that nothing is connected to connector ST1.

HB_FSK700_1020_9161690_Englisch_D.odt / 1022 D / AN9161690
ZN62163/38/25

25

Summary of Contents for Fire Brigade Key FSK700 Series







































Reviews: