MEMOLUB HPS User Manual Download Page 10

Page: 10 / 40

The lengths of tubing that can be used with the Splitter-MEMO applications are

determined by the base-oil viscosity at the working temperature of the grease used. The

table in

Section 5.2

provides information on recommended maximum tube lengths to be

used with the Splitter-MEMO. Contact your MEMOLUB

distributor, PLI, or your

lubricant supplier for information on the temperature at which the base-oil of the grease

being used reaches this viscosity.

3.2 How It Works

An explanation of the operation of the Splitter-MEMO, with diagrams, is provided in the

Appendix. Also provided in the Appendix are dimensional drawings of the system when

used with each of the three sizes of MEMOLUB

Lubricators.

Caution: Splitter-MEMO’s are carefully pre-filled to 100% capacity at the factory with

the same grease ordered in the MEMOLUB

cartridge. Do not open the Splitter-MEMO

or manually activate the Stem Valve. In both cases air will be introduced into the system.

3.3 Retrofitting a MEMOLUB

A MEMOLUB

HPS can be retrofit in the field to a 2-

point Splitter-MEMO. Retrofitting is accomplished by

removing the black timing ring holder from the brass

fitting of the MEMO and placing it on the Splitter-

MEMO.

Retrofitting a MEMOLUB

HPS in the field

may

require

recharging the Splitter-MEMO with the grease being used.

SPLITTER MEMO's purchased without a MEMOLUB

Lubricator have been pre-

charged with lithium-based grease at the factory. If incompatible grease or a special

grease (e.g. food-grade) is to be used, it will be necessary to recharge the Splitter-MEMO.

To do this, use the Zerk grease nipple that is supplied with the Splitter-MEMO to pump

the correct grease through the outlet port labeled #1 (see illustration above). This is the

outlet port closest to the base of the Splitter-MEMO. The Splitter-MEMO must be

recharged without the MEMOLUB

Lubricator mounted on it. Pump grease into outlet

port #1until it seeps through the piston at the top of the Splitter.

The MEMOLUB

HPS with External Power Control or Supply

4.1 The

MEMOLUB

EPC Version

MEMOLUB

HPS User’s Guide

Page

9 of 39

PLI,

LLC

The EPC (External Power Control) version of the MEMOLUB

HPS is

ideal for avoiding over-lubrication in applications where machinery is

used infrequently or intermittently. The MEMOLUB

EPC operates

under its own battery power but the lubricator is turned on and off

externally. A 12” lead-wire extending from the base of the lubricator is

connected to a relay. This relay is opened and closed in concert with

Summary of Contents for HPS









































Search results

Summary of Contents for HPS

Reviews:

Related manuals for HPS

Brands by name

Popular brands

MEMOLUB HPS, User Manual

Search results

Summary of Contents for HPS

Reviews:

Related manuals for HPS

Brands by name

Popular brands