background image

RedHandScope60MHz   

 

Handheld DSO & DMM                                                             

4-Input Connections 

   

4. Input Connections 

4.1 Input Connections 

Description: 

1.

 

The power adapter is supplied for AC power supply and battery recharging. 

2.

 

Multimeter test lead. 

3.

 

Multimeter input jacks, including three circular banana jacks and tow square jacks. The three 

circular  jacks  are  used  for  voltage,  current  and  resistance  inputs,  while  the  two  square  jacks 

are used for capacitance inputs. 

4.

 

Oscilloscope probes. 

5.

 

Oscilloscope channel inputs: the upper one is for Channel 1 (CHI1), while the lower one is for 

Channel 2 (CH2). 

4.2 Description for Front Panel and Keys 

 

Description:

 

1.

 

Power adapter jack. 

2.

 

Serial port. (Option) 

3.

 

USB jack. 

4.

 

Backlight switch. 

5.

 

POWER: Power switch. 

6.

 

A: Multimeter current measurement key. 

7.

 

V: Multimeter voltage measurement key. 

8.

 

R: Multimeter resistance, triode, On/Off and capacitance measurement key.   

9.

 

OSC 

: Oscilloscope left-direction adjustment key. 

10.

 

OSC 

: Oscilloscope right-direction adjustment key. 

11.

 

OSC OPTION: Oscilloscope setting key.   

 

With the combination application  of  the four  keys OSC 

, OSC 

, OSC 

 and OSC 

the  users  can  make  the  following  settings  circularly  by  pressing  OSC  OPTION.  The  settings 

Summary of Contents for RedHand Scope











































































Reviews: