background image

8

12. To activate the timer, turn the pump on and timing will commence.  
The timer reflects each hour of compression. When compression is interrupted  
i.e. the patient is removed from therapy, the timer will suspend timing until the  
patient is reconnected to therapy and therapy is continued.

13. To reset the timer press “RESET” for 5 seconds and it will reset itself.

14. To turn pump off, hold the power button for 5 seconds.
15. To disconnect device remove plug from electrical outlet.

16. Be sure battery is installed in the back side of the device to avoid 

 

an interruption in therapy due to power failure.

17. Respond to the instrument alarms appropriately and refer to troubleshooting 

guide on pump (page 28 of this manual).
18. To remove the sleeves, press the tab on large white (female) connector 
and pull apart. 

Recommendations during operation
• Avoid placing the tubing and/or any connections or components under the patient 
as this may negatively impact the effectiveness of the pump and/or cause a skin 

integrity issue for the patient

• Make sure that there are no kinks in the tubing and that the connectors are 

properly locked.  

• Never apply or remove the sleeves while inflated as this may cause damage 

to the sleeve.

• The parts and/or accessories supplied are specifically designed for use with 
Hemo-Force IPCS control unit. Use of other products in conjunction with the 

system is not recommended.

Alarms and indicators

Indicator Light: Green

Illuminated to indicate power on

Indicator Light: Amber

Flashing to indicate a fault has been detected follow by 
an audio alarm

Indicator Light: Blue

Flashing indicates initialization in process for 10 sec and 
upper display window showing (Int) illuminated indicates 
unit is operational

Blue LED Display

Upper display indicates therapy selected for Calf/Thigh 
(LEG) or FOOT (Ft). Lower display indicates pressure 

delivered to each chamber of compression and alarm 

status for low pressure (LO), high pressure (HI), sleeve 
error (GE) and fault (F).

Timer

Indication of therapy time in hours from commencement 
of therapy per patient

Summary of Contents for Hemo-Force MDS600INT





























Reviews: