MAINTENANCE
English
–
11
General
•
Always use genuine accessories.
Maintenance schedule
In the maintenance schedule you can see which parts of
your machine that require maintenance, and with which
intervals it should take place. The intervals are calculated
based on daily use of the machine, and may differ
depending on the rate of usage.
*See instructions in the section "Machine’s safety equipment".
General inspection
•
Check that nuts and screws are tight.
External cleaning
•
Brush leaves, grass and the like off of the lawn mower.
•
Do not use a high pressure washer to clean the
machine.
•
Never flush water directly on the engine.
•
Clean the air intake on the starter. Check the starter
and starter cord.
•
When cleaning under the cutting deck, turn the
machine with the spark plug upwards. Empty the fuel
tank.
Oil level
The lawn mower should stand on flat ground when you
check the oil level. Check the oil level with the dipstick on
the oil filler cap.
•
Remove the oil cap and wipe the dipstick clean.
•
Put the dipstick back in. The oil filler cap must be
completely screwed down to give a correct picture of
the oil level.
•
If the oil level is low, fill using engine oil up to the upper
level on the dipstick.
Cutting equipment
•
Check the cutting attachment for damage or cracks. A
damaged cutting attachment should always be
replaced.
•
Always ensure the cutter is well ground and balanced
correctly.
Replacing the blades
Dismantling
•
Unscrew the bolt holding the cutter.
•
Remove the old blade. Make sure the blade bracket is
free of damage. Also check that the cutter bolt is
undamaged and that the engine shaft is not bent.
Assembly
•
Make sure the cutter centres correctly on the shaft.
!
WARNING! The user must only carry out
the maintenance and service work
described in this Operator’s Manual.
More extensive work must be carried out
by a service workshop.
Prevent unintentional starting by
removing the ignition cable from the
spark plug.
The life span of the machine can be
reduced and the risk of accidents can
increase if machine maintenance is not
carried out correctly and if service and/or
repairs are not carried out professionally.
If you need further information please
contact your nearest service workshop.
CAUTION! When the machine is tilted, make sure the air
filter always is placed in the highest position.
Before starting
Weekly
maintenance
Monthly
maintenance
General inspection
Spark plug
Air filter
External cleaning
Muffler*
Fuel system
Oil level
Cutting equipment
Cutting cover*
Adjusting the clutch
wire
Engine brake handle*
CAUTION! The blades should be balanced after
sharpening. Balancing, replacing or sharpening the
blades should be conducted by a service workshop.
Damaged blades should be replaced when hitting
obstacles that result in a breakdown. Let the service
centre assess whether the blade can be sharpened or
must be replaced.
!
WARNING! Always wear heavy-duty
gloves when servicing and maintaining
the cutting equipment. The cutters are
very sharp and cuts can occur very
easily.
Summary of Contents for M46-160AWRPX
