Mazda CX-9 2021 Manual Download Page 275 | Manualshive

Page: 275 / 720

background image

Drive Selection

Drive selection is a system to switch the vehicle's drive mode. When the sport mode is
selected, the vehicle's response against accelerator operation is enhanced. This provides
additional quick acceleration which may be needed to safely make maneuvers such as lane
changes, merging onto freeways, or passing other vehicles.

CAUTION

Do not use the sport mode when driving on slippery roads such as wet or snow-covered roads.
It may cause tire slipping.

NOTE



When sport mode is selected, driving at higher engine speeds may increase fuel
consumption. Mazda recommends that you cancel sport mode for normal driving.



Drive mode cannot be switched in the following conditions:



ABS/TCS/DSC is operating



The Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go
function) System/cruise control is operating.



Steering wheel is being operated abruptly

▼

Drive Selection Switch

Press the drive selection switch forward
(“

”) to select the sport mode.

Pull the drive selection switch back
(“

”) to cancel the sport mode.

NOTE



In the following cases, the drive
selection is canceled.



The ignition is switched OFF.



Mazda Radar Cruise Control with
Stop & Go function (MRCC with Stop
& Go function) System/cruise control
is set.



Depending on the driving conditions
when sport mode is selected, the vehicle
may perform shift-down or slightly
accelerate.

▼

Select Mode Indication

The light is illuminated while in SPORT
mode.

When Driving

Drive Selection

4-109

CX-9_8JK1-EA-20G_Edition2_old

2020-7-20 17:31:45

«
...
273
274
275
276
277
...
»

Summary of Contents for CX-9 2021

















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 2021

Brand: A-Tach Mounts Pages: 2

Brand: Jeep Pages: 6

Brand: Dakota Digital Pages: 2

Brand: Dakota Digital Pages: 7

Green Motion DC 22

Brand: Eaton Pages: 65

Brand: Parrot Pages: 19

Brand: Parrot Pages: 88

Brand: Parrot Pages: 2

Brand: Parrot Pages: 2

CK 3000 Evolution

Brand: Parrot Pages: 8

CK 3000 Evolution

Brand: Parrot Pages: 106

CommCenter D1 Series

Brand: Federal Signal Corporation Pages: 16

Cherokee 16 1982

Brand: Jeep Pages: 1311

Stratus LHD 1997

Brand: Chrysler Pages: 1534

inView 360 Fusion

Brand: Safe Fleet Pages: 27

ROADSIDE ASSISTANCE

Brand: Seat Pages: 44

Brand: tams elektronik Pages: 19

Brand: Maserati Pages: 302

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands