Maxwell MW-3818 BK, Manual Instruction

Page: 13 / 44

13
ENGLISH
bowl). The maximal level mark for por-
ridges (except rice) is «8».
– Make sure that there are no foreign objects
in the process chamber and that the bottom
of the bowl (12) and the surfaces of the heat-
ing element (10) and the temperature sensor
(11) are clean and dry.
–
In the middle of the heating element (10)
there is a temperature sensor (11). Make
sure that the movement of the sensor (11) is
not limited.
1.
Put the food into the bowl (12) following the
recommendations given in the recipe (see
the Recipe book).
2.
Place the bowl (12) into the operation cham-
ber evenly so that it is in tight contact with the
heating element (10).
3.
If you are going to steam products, pour
water into the bowl (12) so that boiling water
doesn’t reach the bottom of the steam cook-
ing basket (19); put the products in the
basket (19).
4.
Close the lid (4) until the lock clicks.
Cooking rice
– Measure the required amount of rice with the
measuring cup (21) (one measuring cup (21)
is equal to approximately 160 g of rice), wash
it and put in the bowl (12).
– Pour water up to the corresponding mark on
the «CUP» scale inside the bowl (12).
Example:
After putting four measuring cups (21) of
rice, pour water till the mark «4 CUP» on the
inner side of the bowl (12).
Note: For cooking thin milk porridges, the rec-
ommended proportion of rice and water is 1:3.
USING THE MULTICOOKER
–
During the first operation of the multicooker
some foreign smell from the heating element
can appear. It is normal.
–
During food cooking you may hear clicks; this
means that the heating element is periodi-
cally switched on and off maintaining the set
cooking temperature. It is normal.
–
Every pressing of the control panel (2) but-
tons is accompanied by a short sound signal.
ATTENTION!
– If you pause for more than 10 seconds
when selecting and setting a cooking
program, the unit will be automatically
switched to the selected cooking mode
and the corresponding indicator will
light up.
–
If you have entered wrong program set-
tings and the multicooker is already on,
stop the cooking process by pressing
the «CANCEL» button (16) and reset the
cooking program.
1.
Put the products into the bowl (12) (see
«Products loading»).
2.
Insert the power cord connector into the
connector socket (9) on the unit body (1)
and insert the power cord plug into the mains
socket. There will be a sound signal, the dis-
play will show «0000» symbols.
3.
Select a cooking program by pressing one
of the buttons (13). The indicator of the pro-
gram button will be flashing and the display
(3) will show the cooking time set by default.
4.
To change cooking duration, consequently
press or hold down the «TIME» button (14),
the program operation time will be shown on
the display (3) (see «COOKING PROGRAMS»
table).
5.
In «Multimode» program, you can set the
cooking temperature, pressing the but-
ton (15) «t°» consequently (see «COOKING
PROGRAMS» table).
6.
Go over to setting the delayed start time and
set the delayed start time by pressing or
holding the «DELAYED START» button (17),
the button (17) indicator will be flashing.
Note: If you want to switch the cooking program
on immediately, skip step 6.
7.
After 10 seconds the unit will be automatically
switched to the cooking mode: you will hear
a sound signal and the corresponding indica-
tors will light constantly.
8.
To stop the cooking program, press the
«MAINTAIN t°/CANCEL» button (16).
9.
When the cooking program is over, you
will hear three sound signals, and the unit
will be automatically switched to the keep
warm mode, the multicooker operation time
in keep warm mode will be shown on the
display (3).
10.
To switch the keep warm mode off, press the
«MAINTAIN t°/CANCEL» button (16).
11.
After finishing the multicooker operation,
unplug the unit and disconnect the power
cord from the connector socket (9).
12.
Open the lid (4) by pressing the button (5).
MW-3818.indd 13 21.03.2014 16:50:06