Maxwell MW-1184 G, Manual Instruction

Page: 7 / 20

7
ENGLISH
with warm water and neutral detergent and then
dry thoroughly.
• Clean the motor unit with a soft, slightly damp
cloth and then wipe it dry.
•
Do not immerse the blender body into any liq-
uids or wash it with water.
•
Place the blender on a flat stable surface.
ATTENTION! Continuous operation time of the
blender should not exceed 1 minute, and the
break between operations should be no less
than 2 minutes.
• Do not remove the blender bowl and the bowl
lid during the operation.
USING THE BLENDER
The blender is intended for chopping products,
mixing different ingredients and for making cocktails.
•
Place the blender bowl (3) on the motor unit
(7) and turn it counterclockwise until bumping.
•
Remove the blender bowl lid (2) by rotating it
counterclockwise.
•
Put the necessary ingredients into the bowl (3).
• Cover the blender bowl (3) with the lid (2),
matching the ledges on the lid (2) with the
grooves on the bowl (3), turn the lid (2) clock-
wise until it is fixed and insert the plug/measur-
ing cup (1) into the opening of the lid (2).
• Make sure once again that the blender bowl (3)
is installed correctly and fixed.
• Insert the power plug into the mains socket.
Note: The blender will not be switched on if the
blender bowl (3) is installed incorrectly.
•
Use the operation mode switch (8) to set the
required rotation speed of the knives:
–
«1» (low speed) – for mixing liquid products;
– «2» (high speed) – for liquid and hard prod-
ucts;
– «P» – pulse mode.
• During the operation or between the operation
cycles, you can add the required ingredients
into the bowl (3). To do this, remove the lid plug
(1); you can use it as a beaker for adding nec-
essary liquid ingredients. After adding ingredi-
ents, install the lid plug (1) back to its place. The
lid (1) capacity is 40 ml.
• After the unit’s operation is finished, set the
operation mode switch (8) to the “0” position
and unplug the unit.
•
Remove the blender bowl (3) from the motor
unit (7) by turning it clockwise.
•
Remove the lid (2) from the bowl (3) and take
the processed products out of the bowl (3).
• After the operation is finished, wash the blender
bowl (3).
Note: If food processing is hindered, add some
liquid (water, liquor, juice) into the blender bowl (3).
ATTENTION! Continuous operation time of the
blender should not exceed 1 minute, and the
break between operations should be no less
than 2 minutes.
CLEANING AND CARE
After the unit operation is finished, switch the
blender off by setting the operation mode switch
(8) to the “0” position and unplug it.
•
Remove the blender bowl (3) from the motor
unit (7) by turning it clockwise.
• Take the processed products out of the bowl (3).
•
Wash the bowl (3) preliminarily. Remove the
sealing gasket (5) from the knife block (6). To
remove the knife block (6), turn it in the direc-
tion of the “Unlocked” arrow (clockwise) and
remove it.
WARNING: The cutting edges of the knives are
very sharp and dangerous. Handle them very
carefully.
• Wash the bowl (3), the knife block (6) and the
sealing gasket (5) with warm water and soft
detergent and dry them.
•
Clean the unit body with a soft damp cloth and
then wipe it dry.
•
Do not use coarse sponges, abrasives and sol-
vents to clean the blender.
•
Do not immerse the blender body (7) into
any liquids; do not wash it in a dishwash-
ing machine.
•
Install the sealing gasket (5) into the groove on
the knife block (6).
•
Insert the knife block (6) into the blender bowl
(3) and turn it in the direction of the «Locked»
arrow.
STORAGE
• Perform the requirements of the CLEANING
AND CARE section before taking the unit away
for storage.
• Keep the unit away from children in a clean and
dry place.
Food processing examples
Specified processing time is approximate and
depends on the products quality, their quantity and
chopping degree.
MW-1184.indd 7 03.09.2014 16:54:37