12
2.2 INSTALLATION TO OPERATE A THRUSTER
Before connecting the AA710 to operate a thruster you must ensure that the
thruster has been installed and tested by a
T
uali
¿
ed marine electrician and that
the installation has been completed according to the thruster manufacturer’s
instructions.
5HIHUWRWKHZLULQJGLDJUDPDQGQRWHVVXSSOLHGIRUWKH$$
An isolating switch must be installed for controls if the main breaker or isolator is not
readily accessible from the helm.
,IWKHWKUXVWHUFRQWUROFLUFXLWXVHVQHJDWLYHVZLWFKLQJFRQQHFWDUHOD\EHWZHHQWKH$$
output and the control wire to convert from positive to negative switching.
The stern and bow output locations stated in the wiring are the default locations. These
FDQEHFKDQJHGXVLQJWKH$$VHWXSPHQX
7KHWKUXVWHUPDQXIDFWXUHU¶VVDIHW\UHTXLUHPHQWVIRUWHVWLQJDQGRSHUDWLQJWKHWKUXVWHUPXVW
EHDGKHUHGWRDWDOOWLPHVZKHQXVLQJWKH$$7KHVHLQFOXGHEXWDUHQRWOLPLWHGWR
1HYHURSHUDWHDWKUXVWHUFORVHWRSHRSOHVZLPPLQJ
1HYHUUXQWKHWKUXVWHURXWRIWKHZDWHU1RWHYHQIRUDVKRUWSHULRG$Q\RSHUDWLRQRI
the thruster out of the water can seriously damage the motor.
5XQQLQJDWKUXVWHUZLWKRXWUHVLVWDQFHIURPWKHSURSHOOHUFDQDOVRFDXVHVHULRXVGDPDJH
to the motor.
If the thruster stops giving thrust while the motor is running, turn it off
immediately.
2.2.1 POWER ENABLE SETTING
This is used to activate a power pack. It will time out and switch off after the delay time
selected.
2.3 INSTALLATION TO OPERATE AUXILIARY EQUIPMENT
2XWSXWVIURPWKH$$FDQEHFRQQHFWHGWRFRQWURODX[LOLDU\HTXLSPHQWRQWKHYHVVHO
VXFKDVOLJKWVGHFNRUDQFKRUZDVKSXPSVHOHFWULFFOHDWVDQGGDYLWV8SWRDX[LOLDU\
RXWSXWVFDQEHVHWXSSHUV\VWHP7KHRXWSXWVFDQEHGLVWULEXWHGDFURVVXSWREDVH
stations.
Before connecting the AA710 to operate auxiliary equipment you must ensure
that the equipment has been installed and tested by a quali
¿
ed marine electrician
and that the installation has been completed strictly according to the equipment
manufacturer’s instructions. The equipment must only be used according to the
equipment manufacturer’s instructions.
Refer to the wiring diagrams and notes supplied
IRUWKH$$
An isolating switch must be installed for controls if the main breaker or isolator is not
readily accessible from the helm.
Relays:
,IWKHDX[LOLDU\HTXLSPHQWLVRXWVLGHWKHVSHFL¿FDWLRQRIWKH$$RXWSXWHJ
FXUUHQWJUHDWHUWKDQ$UHOD\VZLOOQHHGWREHLQWHUIDFHGEHWZHHQWKH$$RXWSXW
DQGWKHDX[LOLDU\HTXLSPHQW7KLVDSSOLHVDOVRLIWKHDX[LOLDU\HTXLSPHQWLVUXQQLQJRIID
different power supply.
