manualshive.com logo in svg

Maxim Dallas Semiconductor DS3171, General Description Manual, Page: 148 / 234

Share
Download
Maxim Dallas Semiconductor DS3171 General Description Manual Download Page 148

DS3171/DS3172/DS3173/DS3174 

 

 

148 

 
Register Name: 

BERT.TEICR 

Register Description: 

BERT Transmit Error Insertion Control Register 

Register Address: 

(0,2,4,6)68h 

 
Bit 

#  15 14 13 12 11 10  9  8 

Name 

-- -- -- -- -- -- -- -- 

Default 

0 0 0 0 0 0 0 0 

 
Bit 

# 7 6 5 4 3 2 1 0 

Name 

-- 

--  TEIR2 TEIR1 TEIR0  BEI  TSEI MEIMS 

Default 

0 0 0 0 0 0 0 0 

 

Bits 5 to 3: Transmit Error Insertion Rate (TEIR[2:0]) 

– These three bits indicate the rate at which errors are 

inserted in the output data stream. One out of every 10

n

 bits is inverted. TEIR[2:0] is the value n. A TEIR[2:0] value 

of 0 disables error insertion at a specific rate. A TEIR[2:0] value of 1 result in every 10

th

 bit being inverted. A 

TEIR[2:0] value of 2 result in every 100

th

 bit being inverted. Error insertion starts when this register is written to with 

a TEIR[2:0] value that is non-zero. If this register is written to during the middle of an error insertion process, the 
new error rate will be started after the next error is inserted. 

TEIR[2:0] Error 

Rate 

000 Disabled 

001 

1 x 10

-1

 

010 

1 x 10

-2

 

011 

1 x 10

-3

 

100 

1 x 10

-4

 

101 

1 x 10

-5

 

110 

1 x 10

-6

 

111 

1 x 10

-7

 

 

Bit 2: Bit Error Insertion Enable (BEI)

 – When 0, single bit error insertion is disabled. When 1, single bit error 

insertion is enabled. 

Bit 1: Transmit Single Error Insert (TSEI)

 – This bit causes a bit error to be inserted in the transmit data stream if 

manual error insertion is disabled (MEIMS = 0) and single bit error insertion is enabled. A 0 to 1 transition causes a 
single bit error to be inserted. For a second bit error to be inserted, this bit must be set to 0, and back to 1. Note: If 
MEIMS is low, and this bit transitions more than once between error insertion opportunities, only one error will be 
inserted. 

Bit 0: Manual Error Insert Mode Select (MEIMS)

 – When 0, error insertion is initiated by the TSEI register bit. 

When 1, error insertion is initiated by the transmit manual error insertion signal (TMEI). Note: If TMEI or TSEI is 
one, changing the state of this bit may cause a bit error to be inserted. 

 

 

Summary of Contents for Dallas Semiconductor DS3171











































































































































































































































Reviews:

No comments