manualshive.com logo in svg

Maxim Dallas Semiconductor DS3171, General Description Manual, Page: 128 / 234

Share
Download
Maxim Dallas Semiconductor DS3171 General Description Manual Download Page 128

DS3171/DS3172/DS3173/DS3174 

 

 

128 

Register Name: 

GL.CR1 

Register Description: 

Global Control Register 1 

Register Address: 

002h 

 
Bit 

#  15 14 13 12 11 10  9  8 

Name GWRM INTM 

RESERVED 

-- 

RESERVED

 

RESERVED

 

RESERVED

 

RESERVED

 

Default 

0 0 0 0 0 0 0 0 

 

 

 

 

 

 

 

 

 

Bit 

# 7 6 5 4 3 2 1 0 

Name TMEI 

MEIMS 

GPM1 

GPM0 PMU 

LSBCRE 

RSTDP RST 

Default 

0 0 0 0 0 0 1 0 

 

Bit 15: Global Write Mode (GWRM)

 This bit enables the global write mode. When this bit is set, a write to the 

register of any port will write to the same register in all the ports. Reading the registers of any port is not supported 
and will read back undefined data.  
 

0 = Normal write mode 

 

1 = Global write mode 

Bit 14: 

INT 

pin mode (INTM)

 This bit determines the inactive mode of the 

INT

 pin. The 

INT

 pin always drives low 

when active.  
 

0 = Pin is high impedance when not active 

 

1 = Pin drives high when not active 

Bit 7: Transmit Manual Error Insert (TMEI)

 This bit is used insert an error in all ports configured for global error 

insertion. An error(s) is inserted at the next opportunity when this bit transitions from low to high. The 

GL.CR1

.MEIMS bit must be clear for this bit to operate.  

Bit 6: Transmit Manual Error Insert Select (MEIMS)

 This bit is used to select the source of the global manual 

error insertion signal 
 

0 = Global error insertion using TMEI bit 

 

1 = Global error insertion using the GPIO6 pin 

Bits 5 and 4: Global Performance Monitor Update Mode (GPM[1:0]) 

These bits select the global performance 

monitor register update mode.

 

00 = Global PM update using the PMU bit 
01 = Global PM update using the GPIO8 pin 
1x = One second PM update using the internal one second counter 

Bit 3: Global Performance Monitor Update Register (PMU)

 This bit is used to update all of the performance 

monitor registers configured to use this bit. When this bit is toggled from low to high the performance registers 
configured to use this signal will be updated with the latest count value from the counters, and the counters will be 
reset. The bit should remain high until the performance register update status bit (

GL.SR

.PMS) goes high, then it 

should be brought back low which clears the PMS status bit. 

Bit 2: Latched Status Bit Clear on Read Enable (LSBCRE).

 This signal determines when latched status register 

bits are cleared. 

0 = Latched status register bits are cleared on a write 
1 = Latched status register bits are cleared on a read 

Bit 1: Reset Data Path (RSTDP).

 When this bit is set, it will force all of the internal data path registers in all ports 

to their default state. This bit must be set high for a minimum of 100ns. See the 

Reset and Power-Down

 section in 

Section 

10.3

. Note: The default state is a 1 (after a general reset, this bit will be set to one).

 

 

0 = Normal operation 

 

1 = Force all data path registers to their default values 

Summary of Contents for Dallas Semiconductor DS3171











































































































































































































































Reviews:

No comments