Matrix SETU ATA211 SIP-FXS-FXO System Manual Download Page 143

Page: 143 / 178

Matrix SETU ATA211 System Manual

137

CHAPTER 6

System Status

You may view the status of the System, the Network ports (LAN and WAN), SIP Trunks and Auto Configuration
from Jeeves.

You can also check the status of certain parameters, like the Registration status of SIP Trunks, IP Address and
Subnet Mask of the LAN and WAN port, on the display of the Phone connected to FXS port by dialing the relevant

“System Commands”

Viewing System Status from Jeeves

To view System Status on Jeeves from Admin Mode,

•

Admin

•

Click the

Status

link to open the page.

To view System Status on Jeeves from User Mode,

http://arttel.ru

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-matrix-setu-ata211

Summary of Contents for SETU ATA211 SIP-FXS-FXO



















































































































































































Search results

Summary of Contents for SETU ATA211 SIP-FXS-FXO

Reviews:

Related manuals for SETU ATA211 SIP-FXS-FXO

Brands by name

Popular brands

Matrix SETU ATA211 SIP-FXS-FXO, System Manual

Search results

Summary of Contents for SETU ATA211 SIP-FXS-FXO

Reviews:

Related manuals for SETU ATA211 SIP-FXS-FXO

Brands by name

Popular brands