Matrix SETU ATA211 SIP-FXS-FXO System Manual Download Page 87

Page: 87 / 178

Matrix SETU ATA211 System Manual

Configuring Peer-to-Peer Calling

To use Peer-to-Peer calling, do the following:

•

enable the SIP trunk.

•

set the SIP Trunk Mode to Peer-to-Peer.

•

configure the number callers must dial to reach this SIP trunk as its SIP ID.

•

set the Incoming Call Routing option on the SIP trunk as Route to FXS.

•

configure Outgoing Call Route on the FXS port.

•

configure Incoming Call Routing on the FXO port.

•

configure the Peer-to-Peer table.

If you have not configured the Peer-to-Peer table from the SIP Trunks page under

Basic Settings

, you may do so

now.

Admin

Click the

Advanced Settings

link on the left pane to expand.

Click the

Peer-to-Peer Numbers

link. The Peer-to-Peer Table opens.

In the Peer-to-Peer table, each entry is stored against an Index Number from 001 to 500. The first entry at
Index001 is reserved for No Match Found.

For each Index number,

•

In the

Number

field, enter the peer-to-peer number string—prefix or entire number—that will be dialed.

The number string must not exceed 24 characters. Default: Blank.

http://arttel.ru

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-matrix-setu-ata211

Summary of Contents for SETU ATA211 SIP-FXS-FXO



















































































































































































Search results

Summary of Contents for SETU ATA211 SIP-FXS-FXO

Reviews:

Related manuals for SETU ATA211 SIP-FXS-FXO

Brands by name

Popular brands

Matrix SETU ATA211 SIP-FXS-FXO, System Manual

Search results

Summary of Contents for SETU ATA211 SIP-FXS-FXO

Reviews:

Related manuals for SETU ATA211 SIP-FXS-FXO

Brands by name

Popular brands