Matrix SETU ATA211 SIP-FXS-FXO System Manual Download Page 46

Page: 46 / 178

Matrix SETU ATA211 System Manual

•

For each index number,

•

Enter the desired

Number

(max. 24 characters) you want to store in the table.

The first Index number 001, is reserved for No Match Found. Start your entries from Index 002.

•

For the number you entered, define the

Minimum Digits

, which the system should wait to

receive before considering it as a valid number. Default:01

•

For the number you entered, define the

Maximum Digits

, which the system should wait to

receive before considering it as End of Dialing. Default: 24

•

For the number you entered, select as

Destination Route

the SIP Trunk / FXS port/ FXO port.

At the bottom of the table, select Destination Route for dialed numbers that do not
match with any of the entries configured in this table (No Match Found) by the
Source Port.

http://arttel.ru

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-matrix-setu-ata211

Summary of Contents for SETU ATA211 SIP-FXS-FXO



















































































































































































Search results

Summary of Contents for SETU ATA211 SIP-FXS-FXO

Reviews:

Related manuals for SETU ATA211 SIP-FXS-FXO

Brands by name

Popular brands

Matrix SETU ATA211 SIP-FXS-FXO, System Manual

Search results

Summary of Contents for SETU ATA211 SIP-FXS-FXO

Reviews:

Related manuals for SETU ATA211 SIP-FXS-FXO

Brands by name

Popular brands