Masport Calais Installation Instructions Manual Download Page 13

Page: 13 / 69

Page 13

FLUEING ARRANGEMENTS - HORIZONTAL TERMINATIONS

or Masport Direct Vent (Flex) for Horizontal Terminations

The diagram shows all allowable combinations of vertical runs with horizontal terminations, using two 90

elbows (two

elbows equal one 90

elbow).

A flue guard should be used whenever the termination is lower than the specified minimum or as per local codes.

•

Maintain a 40mm clearance to combustibles.

•

Horizontal flue must be supported every 3 feet.

NOTE: Only the AstroCap (Part #: 946-578/P) and the Riser Flue (Part #: 556310) are approved for Horizontal

Termination installations.

Alternate

Horizontal

Termination

Caps

Alternate:
Horizontal Riser Vent
Terminal
Part # 556310

Notes:

Liner sections should be continuous without any
joints or seams.

Only Flex pipe purchased from Masport may be
used for Flex installations.

Summary of Contents for Calais






































































Search results

Summary of Contents for Calais

Reviews:

Related manuals for Calais

Brands by name

Popular brands

Masport Calais, Installation Instructions Manual

Search results

Summary of Contents for Calais

Reviews:

Related manuals for Calais

Brands by name

Popular brands