Masport Calais Installation Instructions Manual Download Page 68

Page: 68 / 69

Page 68

INSTALLATION

1) Assemble Zero Clearance box as per instructions

on page 6.

DOT NOT INSTALL FRONT PLATE.

2) Place the unit on the stand-offs in the Zero Clear-

ance box.

3) Slide the unit in all the way back.

4) Run required gas and electrical connections to the

Zero Clearance box, both are located on the left
hand side of the unit. See "Gas Supply Line" on
page 9 and "Electrical Supply" on page 9.

5) Attach flue collar to the top assembly. Align with

holes in Zero Clearance box and secure with 4
screws.

6) Install front panel of zero clearance box, secure

using 6 screws.

7) Make the final gas and electrical connections as

per the instruction manual.

Zero Clearance Box

with unit in place.

Zero Clearance Box assembled.

ZERO CLEARANCE

BOX INSTALLATION

Summary of Contents for Calais






































































Search results

Summary of Contents for Calais

Reviews:

Related manuals for Calais

Brands by name

Popular brands

Masport Calais, Installation Instructions Manual

Search results

Summary of Contents for Calais

Reviews:

Related manuals for Calais

Brands by name

Popular brands