Manitowoc Multiplex N2Fusion Service Manual Download

Page: 42 / 64

Part Number 020007115 06/27/2019

Troubleshooting

Section 5

Refrigeration System Diagnostics

REFRIGERATION SYSTEM CHECKLISTS
Installation/Visual Inspection Checklist

Inadequate Clearances

• Check all clearances, on sides and back.

Sides

0" (0 cm)

Back

3” (76mm)

Front

30" (76 cm)

Condenser is dirty

• Clean the condenser

DISCHARGE PRESSURE HIGH CHECKLIST

Air Condenser

•  Dirty condenser fins
•  High inlet air temperature
•  Condenser discharge air recirculation
•  Defective fan motor

Other

•  Overcharged
•  Non-condensable (air) in system
•  Wrong type of refrigerant
•  Non-OEM components in system
•  High side refrigerant lines/component restricted

DISCHARGE PRESSURE LOW CHECKLIST
•  Undercharged
•  Wrong type of refrigerant
•  Non-OEM components in system

SUCTION PRESSURE HIGH CHECKLIST

Improper Installation

• Refer to “Installation/Visual Inspection Checklist”

Discharge Pressure

• Discharge pressure is too high and is affecting suction

pressure

Improper Refrigerant Charge

• Overcharged (also see “Freeze Cycle Discharge Pressure

High Checklist” )

• Wrong type of refrigerant
• Non condensible in system

Components

• Defective compressor

Other

• Non-OEM components in system

SUCTION PRESSURE LOW CHECKLIST

Improper Installation

• Refer to “Installation/Visual Inspection Checklist”

Discharge Pressure

• Discharge pressure is too low and is affecting low side –

refer to “Freeze Cycle Discharge Pressure Low Checklist”

Improper Refrigerant Charge

• Undercharged
• Wrong type of refrigerant

Other

•  Non-OEM components in system
•  Restricted/plugged liquid line drier
•  Restricted/plugged tubing in suction side or liquid line

of refrigeration system

Summary of Contents for Multiplex N2Fusion

































































Search results

Summary of Contents for Multiplex N2Fusion

Reviews:

Related manuals for Multiplex N2Fusion

Brands by name

Popular brands

Manitowoc Multiplex N2Fusion, Service Manual

Search results

Summary of Contents for Multiplex N2Fusion

Reviews:

Related manuals for Multiplex N2Fusion

Brands by name

Popular brands