background image

- 21 -

ATTENZIONE
Qualora si voglia riportare il veicolo allo stato originale, sarà suffi ciente staccare i connettori della centralina e ricollegare i due connettori 
Malossi (

Fig. 17).

Taratura TPS (throttle position sensor) – Fig. 18
- Ruotare il trimmer “LOW” sulla freccia rossa.
- Ruotare la chiave del veicolo su ON.
- Attendere la completa accensione dei 3 led e il successivo spegnimento.

- Ruotare la chiave del veicolo su OFF.
- Portare il trimmer sullo zero.
- Ruotare il trimmer “HIGH” sulla freccia rossa.

WARNING
If you want to bring the vehicle back to its original condition, you must simply disconnect the cdi connectors and reconnect the Malossi 
connectors  (

Fig. 17).

TPS (Throttle Position Sensor) Calibration – Fig. 18
- Rotate the “LOW” trimmer to the red arrow position.
- Turn the ignition key to the “ON” position.
- Wait for all three (3) LEDs to illuminate and then turn off.

- Turn the ignition key to the “OFF” position.
- Rotate the “LOW” trimmer to the “ZERO (0)” position.
- Rotate the “HIGH” trimmer to the red arrow position.

ATTENTION
Dans le cas on veuille remettre le véhicule à son état d’origine, il sera suffi sant détacher les connecteurs du boitier et reconnecter les deux 
connecteurs Malossi (

Fig. 17).

Réglage TPS (Throttle position sensor) – Fig. 18
- Tournez le trimmer “LOW” sur la fl èche rouge.
- Tournez la clé du véhicule sur ON.
- Attendre l’allumage complet des 3 leds et ensuite l’arrêt complet de celles-ci.

- Tournez la clé du véhicule sur OFF.
- Portez le trimmer sur ZERO.
- Tournez le trimmer “HIGH” sur la fl èche rouge.

Summary of Contents for 3117559













































Reviews: