background image

P 15/ 16

R

epair

[5] Diagnosis by Indication lamp

Color of the indication lamp means the followings.
Blinking green: Normal status
Blinking red: Need to recharge the battery cartridge
Lighting-up-red: Recharge the battery cartridge. Nailing can not be performed due to no remaining battery capacity.
Blinking orange after blinking green and red alternatively
for 10 seconds
: Fault detection is running. Remove and reinsert the battery cartridge to reset. If fault detection is 
                          running again, it is malfunction condition as shown in Fig. 30

Fig. 30

Number of
blinking orange

Melting a part of Switch in Contact arm / Disconnection of Trigger switch  Returning Contact arm incompletely

1

Melting a part of Switch in Contact arm / Melting a part of Trigger switch  Returning Trigger incompletely

2

Possible electrical-malfunction

Possible mechanical-malfunction

Melting a part of Switch in Contact arm

Returning Contact arm incompletely

3

Melting a part of Trigger switch

4

Disconnection of DC motor

5

Malfunction on Spark unit

6

C

ircuit  diagram

Fig. D-1 

Color index of lead wires' sheath

Black

Motor

Spark plug

Line filter

Spark unit

Earth terminal for 
connecting to Housing

White
Red

Connector

Connector

Band

Terminal

Switch unit for DC motor

Yellow

Switch unit for Trigger

Flag 
receptacle

Straight 
receptacle

Summary of Contents for Gas nailer GN900SE

















Reviews: