![background image](http://html.mh-extra.com/html/makita/dup361/dup361_instruction-manual_228143021.webp)
21 ENGLISH
Upper shear blade
1.
Apply
the
flat
surface
of
the
diamond
file
to
the
blade
edge.
Push
the
diamond
file
towards
the
tip
of
the
blade
to
sharpen
along
the
entire
blade
edge.
Maintain
the
same
flat
contact
with
the
file
consistently
along
the
entire
blade
edge.
►
Fig.24:
1.
Diamond file
2.
Apply
the
flat
surface
of
the
diamond
file
lightly
to
the
opposite
side
of
the
blade.
Move
the
diamond
file
towards
the
tip
of
the
blade
lightly
to
remove
burrs. ►
Fig.25
NOTICE:
Do not sharpen this side too much. File
lightly only for
removing burrs.
Otherwise the
blade
clearance may
become
too
much
or
the
blade
life
may
be
shortened.
Lower shear blade
1.
Apply
the
round
surface
of
the
diamond
file
to
the
blade
edge.
Push
the
diamond
file
towards
the
tip
of
the
blade
to
sharpen
along
the
entire
blade
edge. ►
Fig.26
2.
Apply
the
flat
surface
of
the
diamond
file
lightly
to
the
opposite
side
of
the
blade.
Move
the
diamond
file
towards
the
tip
of
the
blade
lightly
to
remove
b
urrs. ►
Fig.27
NOTICE:
Do not sharpen this side too much. File
lightly only for
removing burrs.
Otherwise the
blade
clearance may
become
too
much
or
the
blade
life
may
be
shortened.
Adjustment for blade clearance
►
Fig.28:
1.
Plate
fixing
bolt
2.
Lock plate
3.
Blades tightening nut
From
time
to
time,
adjust
the
clearance of
the
shear
blades
as
follows:
1.
Switch on the tool, and pull the switch trigger to
open the
shear
blades.
2.
With shear
blades
open,
switch
off
the
tool.
And
disconnect the connection cord from the
tool.
3.
Loosen
the
plate
fixing
bolt.
And
then
remove
the
lock plate.
4.
Adjust
the
tightness of
the
blades
tightening nut
by
hand
(fastening torque
for
the
blade
tightening nut:
approximately 0.5 N•m).
5.
Install the
lock
plate
and
plate
fixing
bolt
again.
6.
Check
the
tightness of
the
blade
whether
the
blades
never
rattle
but
upper
blade
can
be
opened
or
closed
about
3mm
by
hand.
If
the
blades
are
too
tight
or
loose,
adjust
the
clearance again.
NOTICE:
Pay attention to the clearance of the
blades.
Too
loose
clearance may
result
in
dull
cut,
and
too
tight
blade
clearance may
result
in
overload
for the motor and short running
time of the tool.
Removing or installing shear blades
To
remove
the
shear
blades,
perform
following
steps:
1.
Tilt the opening angle selector lever to the left side
first to
open
the
blades
fully.
2.
Switch on the tool, and pull the switch trigger to
open the
shear
blades.
3.
With shear
blades
open,
switch
off
the
tool.
And
disconnect the connection cord from the
tool.
►
Fig.29
Summary of Contents for DUP361
