![background image](http://html.mh-extra.com/html/makita/dup361/dup361_instruction-manual_228143022.webp)
22 ENGLISH
4.
Remove
two
bolts
near
the
switch
trigger
with
the
hex wrench.
Remove
the
trigger
guard
by
separating the
tongue
on
the
trigger guard from the groove of the housing.
►
Fig.30:
1.
Bolts
2.
Trigger guard
5.
Remove the E-ring on the link arm with a slotted
screwdriver or alike.
►
Fig.31:
1.
E-ring
2.
Link arm
NOTICE:
The
E-ring
is
expendable
part.
Do
not
re-use
the
E-ring
when
reassembling.
6.
Carefully remove the pin.
►
Fig.32:
1.
Pin
7.
Remove
two
bolts
from
the
side
of
the
housing. ►
Fig.33:
1.
Bolts
8.
Carefully remove the upper and lower shears from
the housing.
►
Fig.34
9.
To
separate
the
upper
blade
and
the
lower
blade,
first
loosen
the
plate
fixing
bolt.
Then remove the lock plate.
►
Fig.35:
1.
Plate
fixing
bolt
2.
Lock plate
NOTE:
When
replacing the
blades
for
hard
branch
with
ones
for
thin
branch,
or
vise
versa,
replace
the
plate
fixing
bolt
as
well.
10.
Loosen
and
remove
the
blades
tightening nut.
►
Fig.36:
1.
Blade tightening nut
2.
Blade
tightening bolt
NOTE:
When
replacing the
blades
for
hard
branch
with
ones
for
thin
branch,
or
vise
versa,
replace
the
blade
tightening bolt
as
well.
To
install
the
shear
blades,
perform
the
procedures above
in
reverse.
Make
sure
all
the
bolts
are
securely
tightened.
After
installing
the
blade,
always
adjust
the
blade
clearance. (Refer
to
“Adjustment
for
blade
clearance”.)
To
install
the
shear
blades,
perform
the
procedures above
in
reverse.
When
installing
the
shear
blades,
pay
attention to the following points:
•
Apply machine
oil
or
grease
on
to
the
blade
tightening bolt
and
between
the
blades.
•
If
you
can
not
place
the
plate
fixing
bolt
properly,
first,
remove
the
O-ring
and
the
plate
fixing
bolt
from the lock plate.
And then overturn the lock plate,
and
return
the
O-ring
and
the
plate
fixing
bolt.
•
When installing the trigger guard, align the tongue
of the trigger guard with the groove of the housing.
►
Fig.37
•
Make sure
all
the
bolts
are
securely
tightened.
•
After installing
the
blade,
always
adjust
blade
clearance. (Refer
to
“Adjustment
for
blade
clearance”.)
•
After installing
the
blade,
always
adjust
cutting
depth.
(Refer
to
“Cutting
depth
adjustment”.)
Trouble shooting
Before
making
a
request
for
repairs,
check
for
trouble
by
yourself.
If
any
abnormality
is
found,
control
your
tool
according to the description of this manual. If the
remedy
mentioned below
cannot
solve
the
problem,
ask
your local authorized
service center for repair. Never tamper or dismount any
part contrary to the description.
State of
abnormality
Probable cause
(malfunction)
Remedy
The
she
ar
blad
e
doe
s not move even
after pulling the
switch trigger.
The
batt
ery
is
low.
Charge
the
battery.
I/O switch is "Off"
position.
Press the I/O switch to
"I" position.
The shears are
locked.
Unlock
the
shears
by
performin
g the steps in "Switch
action".
Connection cord
is loose.
Check the connecting
points
of
the
switch
box
and
shears of connection
cord.
Summary of Contents for DUP361
