Magpowr Maxcess DLCA NET-ECAT User Manual Download Page 66 | Manualshive

Page: 66 / 72

background image

WEB SERVER

www.maxcessintl.com

DLCA NET-ECAT

MI 850A365 1

Page 66 of 72

10.0

Web server

Access the web server in the DLCA NET-ECAT
An Ethernet connection must be made to Ethernet Port 2 only. The
DLCA NET-ECAT must be disconnected from the EtherCAT network
and then power must be cycled.

The DLCA NET-ECAT will allow non-EtherCAT traffic on Ethernet
Port 2 after restarting as long as no EtherCAT traffic is detected on
either Ethernet port.

Open a browser and type into the address bar:

http://10.0.0.113

This is the default IP Address for the DLCA NET-ECAT. The IP
Address is not changeable for the DLCA NET- ECAT.

The DLCA NET-ECAT will show a web page similar to below.
Navigate to other pages using the links in the left menu area. The
other pages will show parameters and provide links to allow
editing parameters and performing calibrations.

The tension is displayed as a real number with the decimal point
position included from parameter P.05 and P.07 in section 7.4.

Figure 14. Sample web server page

«
...
64
65
66
67
68
...
»

Summary of Contents for Maxcess DLCA NET-ECAT









































































Reviews:

No comments

Related manuals for Maxcess DLCA NET-ECAT

Brand: Hama Pages: 8

Brand: Bad Cat Pages: 9

65 Princeton Reverb

Brand: Fender Pages: 2

Brand: icon Audio Pages: 5

Brand: NAD Pages: 2

Brand: D.A.S. Pages: 15

Brand: Advance acoustic Pages: 18

Brand: Vox Pages: 2

Brand: O Audio Pages: 12

Brand: Cloud Pages: 9

Brand: Bazooka Pages: 6

Brand: Texas Instruments Pages: 10

3W Amplified Phone Neckloop

Brand: Spy Earpice Pages: 3

BLACK CORE FIVE

Brand: Magnat Audio Pages: 57

Brand: Chord Pages: 4

Brand: Ibiza sound Pages: 18

Brand: Eden Pages: 7

Brand: Crate Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands