Magpowr Maxcess DLCA NET-ECAT User Manual Download Page 44 | Manualshive

Page: 44 / 72

background image

PARAMETERS

www.maxcessintl.com

DLCA NET-ECAT

MI 850A365 1

Page 44 of 72

7.7

Password

Parameter Description

Range

P.00

Password
When the DLCA NET-ECAT is locked, all parameters will be
viewable but cannot be changed and no calibrations can be
performed.

To lock or unlock the DLCA NET-ECAT press [Enter] to show
the lock and unlock status, displayed as ULOC for unlocked
and LOC for locked.

To lock the DLCA NET-ECAT the password must be entered
twice. To unlock the DLCA NET-ECAT the password only
needs to be entered once.

To lock the DLCA NET-ECAT
Press [Enter] again and the display will show PAS1, press
[Enter] and enter the password using the [+] and [-] buttons.
Pres and hold [Enter] for two seconds to enter the password.

The display now shows PAS2. Press [Enter] and enter the
same password using the [+] and [-] buttons. Press and hold
[Enter] for two seconds to enter the password.

The display now shows LOC for locked. Press [Enter] to
return to displaying tension.

To unlock the DLCA NET-ECAT
Press [Enter] again and the display shows PAS1. Press [Enter]
and enter the password using the [+] and [-] buttons. Press
and hold [Enter] for two seconds to enter the password.

The display now shows ULOC if the correct password was
entered. Press [Enter] to return to displaying tension.

If the password was incorrect, the display shows LOC and the
DLCA NET-ECAT is still locked. Press [Enter] to return to
displaying tension, and then repeat the unlock procedure.

The backdoor code is 6195.

{0, 9999}

«
...
42
43
44
45
46
...
»

Summary of Contents for Maxcess DLCA NET-ECAT









































































Reviews:

No comments

Related manuals for Maxcess DLCA NET-ECAT

Brand: QSC Pages: 48

Brand: E&I Pages: 12

belles Soloist 3

Brand: Power Modules Pages: 7

Brand: Linear Technology Pages: 9

Brand: Optimus Pages: 14

Brand: ifi Pages: 14

Brand: Bang & Olufsen Pages: 12

Brand: MTX Pages: 6

Brand: Skytec Pages: 26

Brand: Neets Pages: 20

TUBE5 Celestion

Brand: Harley Benton Pages: 28

Brand: Audionet Pages: 11

Brand: Suhr Pages: 7

Brand: PA Pages: 9

Brand: Harman Kardon Pages: 29

Brand: JET CITY AMPLIFICATION Pages: 18

Brand: Laney Pages: 5

Twilighter Stereo

Brand: Magnatone Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands