Magnum 261815 Operation Download

Page: 30 / 84

Technical Data

312001P

Technical Data

AGNUM

X5 (Series D)

AGNUM

X7 (Series C)

Working pressure range

0-3000 psi (0-21 MPa, 0-207 bar)

Electric motor

9.0A (open frame, universal)

Operating horsepower

1/2

5/8

Maximum delivery (with tip)

0.27 gpm (1.02 lpm)

0.31 gpm (1.17 lpm)

Paint hose

1/4 in. x 25 ft (6.4 mm x 7.5 m)

Maximum tip hole size

0.015 in. (0.38 mm)

0.017 in. (0.43 mm)

Weight, sprayer only

13.3 lb (6.0 kg)

23.3 lb (10.6 kg)

Weight, sprayer, hose & gun

16.5 lb (7.5 kg)

26.5 lb (12.0 kg)

Dimensions (Upright):

Length

14.5 in. (36.8 cm)

19.3 in. (49.0 cm)

Width

12.4 in. (31.5 cm)

15.3 in. (38.9 cm)

Height

17.9 in. (45.5 cm)

37.0 in. (94.0 cm)

Dimensions (Folded):

Length

N/A

19.3 in. (49.0 cm)

Width

N/A

15.3 in. (38.9 cm)

Height

N/A

29.2 in. (74.2 cm)

Power cord

18 AWG, 3-wire, 6 ft (1.8 m)

Fluid inlet fitting

3/4 in. internal thread (standard garden hose thread)

Fluid outlet fitting

1/4 NPSM external thread

Inlet screen (on suction tube)

35 mesh (450 micron)

Wetted parts, pump & hose

stainless steel, brass, leather, ultra-high molecular weight polyethylene

(UHMWPE), carbide, nylon, aluminum, PVC, polypropylene, fluroelastomer

Wetted parts, gun

aluminum, brass, carbide, nylon, plated steel, stainless steel, UHMWPE, zinc

Generator requirement

1500 Watt minimum

Electrical power requirement

120 Vac, 60 Hz, 15A, 1 phase

Storage temperature range

◆❖

-30° to 160°F (-35° to 71°C)

Operating temperature range

✔

40° to 115°F (4° to 46°C)

◆

When pump is stored with non-freezing fluid. Pump damage will occur if water or latex paint freezes in
pump.

❖

Damage to plastic parts may result if impact occurs in low temperature conditions.

✔

Changes in paint viscosity at very low or very high temperatures can affect sprayer performance.

Summary of Contents for 261815





















































































Search results

Summary of Contents for 261815

Reviews:

Related manuals for 261815

Brands by name

Popular brands

Magnum 261815, Operation

Search results

Summary of Contents for 261815

Reviews:

Related manuals for 261815

Brands by name

Popular brands