Magnum 261815 Operation Download

Page: 19 / 84

Shutdown and Cleaning

312001P

Power Flush

Power flushing is a faster method of flushing. It can
only be used after spraying water-based coatings.

1. Relieve pressure, page 10.

2. Remove tip and guard assembly from gun and

place in waste pail.

3. Place empty waste and

paint pails side by side.

4. Lift suction tube and prime tube from paint pail.

Let them drain into paint for a while.

5. Place suction and prime tube in waste pail.

6. Turn Pressure Control knob to the

Prime/Clean setting.

7. Screw power flush attachment

to garden hose. Close valve.

8. Turn on water. Open valve.

Rinse paint off suction tube,
prime tube and inlet screen.

9. Turn lever to close power flush

attachment.

10. Unscrew inlet screen from suction

tube. Place inlet screen in waste
pail.

11. Connect garden hose to suction

tube with Power Flush attachment.
Leave prime tube in waste pail.

12. Turn power switch ON.

13. Open lever on Power

Flush attachment.

14. Circulate water through sprayer, into waste pail,

for 20 seconds.

15. Turn power switch OFF.

ti9726a

ti9344a

ti9413a

ti9727a

ti2040a

ti2042a

ti5580a

OPEN

ti2043a

ti2018a

Summary of Contents for 261815





















































































Search results

Summary of Contents for 261815

Reviews:

Related manuals for 261815

Brands by name

Popular brands

Magnum 261815, Operation

Search results

Summary of Contents for 261815

Reviews:

Related manuals for 261815

Brands by name

Popular brands