Magnum 261815 Page 29 Operation Download

Page: 29 / 84

Troubleshooting

312001P

Fan pattern varies dramatically
while spraying.

Sprayer does not turn on promptly
when resuming spraying.

Pressure control switch is worn
and causing excessive pressure
variation.

Take sprayer to Graco/M

AGNUM

authorized service center.

Cannot trigger spray gun.

Spray gun trigger lock is locked.

Rotate trigger safety lever to
unlock trigger lock, page 10.

Paint is coming out of pressure
control switch.

Pressure control switch is worn.

Take sprayer to Graco/M

AGNUM

authorized service center.

Prime/Spray valve actuates
automatically relieving pressure
through prime tube.

System is over pressurizing.

Take sprayer to Graco/M

AGNUM

authorized service center.

Paint leaks down outside of pump. Pump packings are worn.

Replace pump packings.

Motor is hot and runs intermit-
tently. Motor automatically shuts
off due to excessive heat. Dam-
age can occur if cause is not cor-
rected.

See Thermal Overload, page 7.

Vent holes in enclosure are
plugged or sprayer is covered.

Keep vent holes clear of
obstructions and overspray and
keep sprayer open to air.

Extension cord is too long or not a
heavy enough gauge.

Replace extension cord. Read
Grounding and Electrical
Requirements, page 7.

Unregulated electrical generator
being used has excessive voltage.

Use electrical generator with a
proper voltage regulator. Sprayer
requires 120VAC, 60 Hz,
1500-Watt generator.

Problem

Cause

Solution

Summary of Contents for 261815





















































































Search results

Summary of Contents for 261815

Reviews:

Related manuals for 261815

Brands by name

Popular brands

Magnum 261815, Operation

Search results

Summary of Contents for 261815

Reviews:

Related manuals for 261815

Brands by name

Popular brands