Magnum Energy MMS Series Owner'S Manual Download Page 2 | Manualshive

Page: 2 / 58

background image

© 2017 Sensata Technologies

i

Disclaimer of Liability

The use of this manual and the conditions or methods of installation,
operation, use, and maintenance of the MMS Series inverter/
charger are beyond the control of Sensata Technologies. Therefore,
this company assumes no responsibility and expressly disclaims
any liability for loss, damage, or expense whether direct, indirect,
consequential, or incidental that may arise out of or be in any way
connected with such installation, operation, use, or maintenance.
Due to continuous improvements and product updates, the images
shown in this manual may not exactly match the unit purchased.

Restrictions on Use

The MMS Series inverter/charger may only be used in life support
devices or systems with the express written approval of Sensata.
Failure of this inverter can reasonably be expected to cause the
failure of that life support device or system, or to affect the safety
or effectiveness of that device or system. If the MMS Series inverter
fails, it is reasonable to assume that the health of the user or other
persons may be endangered.

Copyright Notice

Copyright © 2017 by Sensata Technologies. All rights reserved.
Permission to copy, distribute, and/or modify this document is
prohibited without express written permission from Sensata.

Document Information

Description – MMS Series Owner’s Manual
Part Number and Revision – 64-0036 Rev C
Date Published – April 2017
This entire manual is available for download—with many of the
diagrams in color—on our website at:

www.SensataPower.com

Contact Information

For Magnum Energy products:

Sensata Technologies
Phone: (425) 353-8833
Fax: (425) 353-8390

www.SensataPower.com

Record the unit’s model and serial number in case you need to
provide this information in the future.

Model:

Serial Number:

MMS1012

WU1/U1

MMS1012-G

WU1/U1

«
1
2
3
4
...
»

Summary of Contents for MMS Series



























































Reviews:

No comments

Related manuals for MMS Series

Brand: Bang & Olufsen Pages: 44

Brand: Baldor Pages: 55

blueplanet 3.0 TL3 M2 WM OD IIG0

Brand: Kaco Pages: 262

Brand: PowerConnections Pages: 10

VENUS X8K LEGENDARY

Brand: RGBlink Pages: 33

Brand: Midian Pages: 28

EXT-DVI-2-HDSDISSL

Brand: Gefen Pages: 21

Brand: Edimax Pages: 2

Brand: Badger Meter Pages: 12

Brand: April Music Pages: 20

Brand: PRO SIGNAL Pages: 2

GlobeTrotter Ex GE 0003

Brand: Option Audio Pages: 4

Brand: Midea Pages: 86

Brand: Schumacher Electric Pages: 40

Autotransformer MW 1700

Brand: Fronius Pages: 15

MOB31-12HFN1-QRD0GW

Brand: Midea Pages: 65

Brand: HEIDENHAIN Pages: 26

CIMR-SSA Series

Brand: YASKAWA Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands