Magnum Energy MMS Series Owner'S Manual Download Page 10 | Manualshive

Page: 10 / 58

background image

© 2017 Sensata Technologies

1

1.0 Introduction

Congratulations on your purchase of an MMS Series inverter/charger
from Sensata Technologies. This product is designed especially for
your small home or mobile application. Powerful, yet simple to use,
this product will provide you with years of trouble-free use.

1.1

MMS Series Models

MMS1012

– a 1000 watt inverter/charger with a 50-amp, 4-stage

Power Factor Correction (PFC) charger. The AC input and output
are provided with pigtail wires to allow hardwiring to a main AC
distribution panel and to an inverter sub-panel. Features isolated
input/output neutrals for mobile applications. Includes a 15-foot
battery temperature sensor.

Figure 1-1, MMS1012 Model Inverter/Charger

MMS1012-G

– a 1000 watt inverter/charger with a 50-amp, 4-stage

PFC charger. The AC input is provided by a standard 3-foot plug-in
power cord, and the AC output is provided by a standard GFCI two plug
outlet. Features isolated input/output neutrals for mobile applications.
Includes a 15-foot battery temperature sensor.

Figure 1-2, MMS1012-G Model Inverter/Charger

Introduction

«
...
8
9
10
11
12
...
»

Summary of Contents for MMS Series



























































Reviews:

No comments

Related manuals for MMS Series

Brand: Parker Pages: 99

Brand: D-Link Pages: 6

Brand: Baldor Pages: 55

Brand: YASKAWA Pages: 67

Brand: Delta Electronics Pages: 14

Brand: Parasound Pages: 7

Brand: ADF Web Pages: 32

Brand: Westinghouse Pages: 197

Brand: K1EL Pages: 5

Symo GEN24 10.0

Brand: Fronius Pages: 120

Brand: CYP Pages: 24

Brand: Modernum Pages: 13

Brand: Black Box Pages: 28

Brand: Ocean Matrix Pages: 12

Brand: Wachendorff Pages: 69

SUNNY TRIPOWER 15000TL Economic Excellence

Brand: SMA Solar Technology Pages: 2

SUNNY CENTRAL 250U

Brand: SMA Pages: 48

Sunny Boy SWR 1800U

Brand: SMA Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands