UNLOADING AND ASSEMBLY
169558
34
Revision D
DETAILED PROGRAMMING INSTRUCTIONS
(Key ON / Engine Running or Not / Header Disengaged).
(Press
PROGRAM
and
SELECT
on CDM to enter Programming Mode).
NOTE: ENGINE MUST BE RUNNING TO CALIBRATE SENSORS
.
L1 C x x x || W I N D R O W E R
S E T U P ?
L2 M x x x ||
N O
/
Y E S
C A B
D I S P L A Y
S E T U P ?
L1
C x x x || S E L E C T H E A D E R
T Y P E ?
L2
M x x x ||
D R A P E R
L1
C x x x || S E L E C T H E A D E R
T Y P E ?
L2
M x x x ||
A 3 0
A U G E R
L1
C x x x || S E L E C T H E A D E R
T Y P E ?
L2
M x x x ||
A 4 0
A U G E R
L1
C x x x || T I L T C Y L I N S T A L L E D ?
L2
M x x x ||
N O
/
Y E S
L1
C x x x || R E E L F O R E / A F T ?
L2
M x x x ||
N O
/
Y E S
L1
C x x x || K N I F E O V E R L O A D
S P D ?
L2
M x x x || 1 0 0 0 S P M
L1
C x x x || H E A D E R I N D E X
M O D E ?
L2
M x x x || R E E L & C O N V E Y O R
L2
M x x x || R E E L O N L Y
L1
C x x x || R E T U R N T O C U T
M O D E ?
L2
M x x x || H E I G H T & T I L T
L2
M x x x || H E I G H T O N L Y
L1
C x x x || H E A D E R C U T W I D T H ?
L2
M x x x || 2 0 . 5 F E E T
L1
C x x x || H A Y C O N D I T I O N E R ?
L2
M x x x ||
N O / Y E S
L1
C x x x || A U G E R H D R R E E L
S P D
L2
M x x x ||
R P M / M P H
L2
M x x x ||
R P M / K P H
L1
C x x x || S E T T I R E S I Z E ?
L2
M x x x || 1 8 . 4 X 2 6 T U R F
L2
M x x x || 1 8 . 4 X 2 6 B A R
L2
M x x x || 2 3 . 1 X 2 6 T U R F
L2
M x x x ||
6 0 0 - 6 5
R 2 8
L2
M x x x ||
5 8 0 / 7 0 R 2 6
T U R F
L1
C x x x || S E T
E N G I N E
I S C
R P M ?
L2
M x x x ||
N O / Y E S
S E T
C O N T R O L
L O C K S ?
L1
C x x x || P R E S S
H A Z A R D
T O
S E T
L2
M x x x || I S C
R P M
O N
L1
C x x x || E X I T
E N G I N E
I S C ?
L2
M x x x ||
N O / Y E S
Programming Menu Flow Chart for Software version C107 and M102 (or higher)
If "NO" then jump to:
If the REEL SPEED sensor is not “installed” (A30
Auger Header selected) in the WINDRWR SETUP
menu, the INDEX mode should be suppressed.
If the HEADER TILT sensor is not “installed” (no
expansion module installed), then the RTC mode
should default to HEIGHT only.
Selects the header type, the selected header will
be flashing. The “factory” default to be DRAPER.
If the A30 is selected then the reel speed should be
suppressed as there is no reel speed sensor.
If a DRAPER or A40 is selected, the reel speed
should be enabled (with expansion module
installed).
Knife Overload Speed should be suppressed
unless the expansion module is installed.
AUGER HEADER ONLY
Pressing “Select” goes to Exit Engine ISC
For IMPERIAL display.
If “NO” then jump to:
If Choosing “YES” pressing “hazard”, choosing On
sets ISC to 2000 rpm
NOTE:
Set CUT WIDTH to represent actual
cutting width. This value should be less than actual
header width to accurately measure cut acres.
DRAPER HEADER ONLY. Default will be flashing.
Use “arrow” keys to select.
Use the “arrow” keys to set the header cut width.
NOTE:
When HYDRAULIC TILT CYLINDER is
physically installed, selecting “yes” will make this
cylinder operational. The tilt “reading” on the CDM
will only be active if an expansion module is
installed.
For METRIC display.
Pressing “SELECT” will go to the next line 1 (L1)
menu selection. The turn signal “arrow” keys are
used to change the values.
(continued next page)
NOTE: 2000 rpm SHOULD BE 2300 rpm.
