English
3
• Over torque (exceeding stated maximum capacity by
130% can result in damage, breakage or affect accuracy).
• Avoid use of solvents, chemicals, liquids.
• Do not attempt to disassemble or repair. Refer to an
authorised service center.
• Guard against snagging of clothing, hair, jewellery or
anything that could impair movement of the product or
workpiece and lead to damage or injury.
CAUTION:
• Hard impacts or dropping the wrench may impair
accuracy of the wrench. If the wrench is dropped
or receives a sharp impact have the wrench
accuracy checked.
• To ensure correct operation and accuracy this product
must be calibrated periodically in line with standards.
Additional Safety Information
WARNING:
Never modify the wrench. Damage or
personal injury could result.
WARNING: ALWAYS
use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or
dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
FCC Compliance Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
IC Compliance Statement
This device contains license-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic
Development Canada’s license-exempt RSS(s). Operation is
subject to the following two conditions:
1 . This device may not cause interference.
2 . This device must accept any interference, including
interference that may cause undesired operation of
the device.
The label on your wrench may include the following symbols.
The symbols and their definitions are as follows:
V ......................... volts
Hz .......................hertz
min .....................minutes
or DC ......direct current
...................... Class I Construction
(grounded)
…/min ..............per minute
BPM ....................beats per minute
IPM .....................impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM ....................strokes per minute
A .........................amperes
W ........................watts
or AC ...........alternating current
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
no .......................no load speed
n .........................rated speed
......................earthing terminal
.....................safety alert symbol
.....................visible radiation
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
Charging the Battery (Fig. B–D)
1. Connect the USB cable
12
to charging dock
13
and
charger
11
as shown in Fig. B.
2. Plug the charger into an appropriate outlet.
3. Place the wrench in the dock, making sure the wrench is
fully seated in the charger.
4. Fully charge the wrench for 4 hours.
-
Fig. C shows the screen when battery is charging:
LEDs will be off and the OLED display will blink the
charge level.
-
Fig. D shows the screen when battery is fully
charged: LEDs will be off and the OLED display will
display a white background. The charge level will
display fully charged battery icon.
5. To remove the wrench from the charger, pull the wrench
out of the charger.
nOTE:
To ensure maximum performance and life of
lithium-ion battery charge the battery fully before
first use.
12
Fig. B
11
13
