Lyngdorf TDAI-2170 Owner'S Manual Download | Manualshive

Page: 41 / 60

background image

41

input. See “Connecting the subwoofer” chapter.

5.6.4 Digital output

The digital output can be set to Off or output a high pass, low pass or full range signal – or it can be

dedicated to a headphone amp or set as a Tape Out.

Digital out

The available settings are:

High pass

removes the frequencies below the crossover frequency.

Low pass

removes the frequencies above the crossover frequency.

Full range

allows the signal to pass unfi ltered.

Headphone

disables RoomPerfect™, voicings are still available. Muting the TDAI-2170 will only mute

the speakers, not this output.

Headphone

disables RoomPerfect™, voicings are still available. Muting the TDAI-2170 will only mute

the speakers, not this output.

Tape Out

disables RoomPerfect™, voicings and volume control.

«
...
39
40
41
42
43
...
»

Summary of Contents for TDAI-2170





























































Reviews:

No comments

Related manuals for TDAI-2170

Brand: Kramer Pages: 15

Brand: Sponsler Pages: 4

Brand: Korg Pages: 31

Brand: Signal Pages: 16

Brand: SAL Pages: 40

Brand: Neets Pages: 20

Brand: R.V.R. Electronica Pages: 36

Brand: Roland Pages: 6

POWER 400 - POWER 400 AMPLIFIER

Brand: Jensen Pages: 44

Brand: Lanzar Pages: 16

CROWN CDi DriveCore Series

Brand: Harman Pages: 2

Brand: SUPRO Pages: 8

Blues-junior IV

Brand: Fender Pages: 16

ATLONA AT-UHD-CAT-2

Brand: Panduit Pages: 18

Euro Rack Classic VCA

Brand: Oakley Sound Pages: 7

Brand: Tavish Design Pages: 34

Brand: Ibiza sound Pages: 24

Brand: ZETA Music Systems Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands