Lyngdorf TDAI-2170 Owner'S Manual Download | Manualshive

Page: 30 / 60

background image

30

4.3 Volume

4.3.1. Default volume

The default volume setting controls the default volume at startup.

4.3.2 Maximum volume

The maximum volume setting is a safety precaution used for limiting the maximum volume which can
be achieved by spinning the wheel or increasing volume via the remote. This can be set to protect your
loudspeakers against overload.

4.4 Voicings

Enables and disables voicings to enable quicker selection of your preferred equalization.

4.5 Display

4.5.1 Display brightness

Display brightness is used to control the brightness of the display.

4.5.2 Display timeout

If enabled, the main display will switch off after 10 seconds of inactivity.

«
...
28
29
30
31
32
...
»

Summary of Contents for TDAI-2170





























































Reviews:

No comments

Related manuals for TDAI-2170

Brand: JBL Pages: 22

Brand: Laney Pages: 14

Brand: Lab.gruppen Pages: 13

Brand: QUAD Pages: 10

Brand: QUAD Pages: 29

Brand: QUAD Pages: 6

Brand: Technics Pages: 264

HF300-3815 Series

Brand: C-Data Pages: 7

DANTE VIRGIL OB

Brand: Glensound Pages: 26

Brand: Alpine Pages: 19

Brand: ELECTROCOMPANIET Pages: 8

Brand: Summit Audio Pages: 20

Brand: Boston Pages: 12

Brand: Omnitronic Pages: 20

iTracker One Pre

Brand: Focusrite Pages: 15

Brand: Elektor Pages: 48

Blues-junior IV

Brand: Fender Pages: 16

Brand: W Audio Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands