Lyngdorf TDAI-2170 Owner'S Manual Download | Manualshive

Page: 39 / 60

background image

39

5.6.2 Main speaker output

The available settings are:

High pass

removes the frequencies below the crossover frequency.

Low pass

removes the frequencies above the crossover frequency.

Full range

allows the signal to pass unfi ltered.

Off

mutes the output.

5.6.3 Analog output

The available settings are:

High pass

removes the frequencies below the crossover frequency.

Low pass

removes the frequencies above the crossover frequency.

Full rang

e allows the signal to pass unfi ltered.

Headphone

disables RoomPerfect™, voicings are still available. Muting the TDAI-2170 will only mute

the speakers, not this output.

Tape Out

disables RoomPerfect™, voicings and volume control.

«
...
37
38
39
40
41
...
»

Summary of Contents for TDAI-2170





























































Reviews:

No comments

Related manuals for TDAI-2170

Brand: Panasonic Pages: 5

Brand: Randall Pages: 12

Brand: JBL Pages: 470

Brand: JBL Pages: 27

Brand: JBL Pages: 4

Grand Touring Series GTO1004

Brand: JBL Pages: 27

Grand Touring Series GTO1004

Brand: JBL Pages: 4

Brand: dB Technologies Pages: 133

Brand: Yamaha Pages: 84

Brand: Meicheng Pages: 23

SHUTTLE MAX 12.0

Brand: Genz Benz Pages: 9

Brand: Alesis Pages: 16

Brand: DTC Audio Pages: 4

Brand: Rega Pages: 17

Brand: zapco Pages: 9

Brand: PrimaLuna Pages: 8

Brand: Crown Pages: 1

Brand: Sansui Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands