manualshive.com logo in svg

Lucent Technologies PARTNER Voice Messaging PC Card Release 2, Installation And Programming

Share
Download
Lucent Technologies PARTNER Voice Messaging PC Card Release 2 Installation And Programming Download Page 38

Changing the System Manager’s Password

Issue  1   August 1998

4-11

   

Changing the System Manager’s 
Password

This section tells you how to change the System Manager’s password (for 
mailbox 0). The factory-set password for mailbox 0 is 1234. To prevent 
unauthorized programming of the system, you should change the default 
password immediately after installation. You must assign four digits for a 
password. It is recommended that you create a password from random, 
nonsequential digits.

You cannot reinitialize the System Manager’s password.

 If you change the 

password and forget it, you can contact the National Customer Care Center at 1 
800 628-2888 or call your Lucent Technologies Representative or local 
Authorized Dealer for assistance.

To change the password for mailbox 0:

1. Log into System Administration according to the appropriate procedure.

2. Press 

5

 to change the password.

The prompt asks you to enter your new password and press 

#

.

3. Enter four digits for the new password and press 

#

.

The prompt asks you to re-enter your new password.

4. Re-enter your new password and press 

#

.

The new password is now active.

Summary of Contents for PARTNER Voice Messaging PC Card Release 2




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands