manualshive.com logo in svg

Lucent Technologies PARTNER Voice Messaging PC Card Release 2, Installation And Programming

Share
Download
Lucent Technologies PARTNER Voice Messaging PC Card Release 2 Installation And Programming Download Page 25

Installation Instructions

3-2

Issue  1   August 1998 

Important Safety Instructions

Always follow these basic safety precautions when using this product:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Do not drop, bend, or crush the card.

4. Keep the card away from moisture, high temperatures, and direct sunlight.

5. Keep the connector on the card clean.

!

CAUTION:

Before starting, verify that you have batteries installed in the 
communications system processor module. (If extension 10 shows the 

ReplaceSysBat W/Power On

 message in the display, replace the batteries 

without turning off the system.) 

!

CAUTION:

To avoid damage to the communications system processor module or to the 
card, do not install or remove the card when power is on.

1. Power down the communications system before inserting or removing the 

PARTNER Voice Messaging PC Card. 

a. If you have a 5-Slot carrier, turn the On/Off Switch to Off (“O”).

Figure 3-1.

PARTNER ACS Processor Power Cord Connection

b. For all communications systems, disconnect the power cord from 

the power jack on your installation.

Stand-Alone

PARTNER ACS

Processor Module

2-Slot Carrier

PFT

PFT

E

X

T

E

N

S

I

O

N

S

L

I

N

E

S

PFT

PFT

E

X

T

E

N

S

I

O

N

S

L

I

N

E

S

PFT

L

I

N

E

S

MUSIC

ON
HOLD

VOL

PAGE

1

2

3

4

16

17

18

19

20

21

15

10

11

12

13

14

MODULE

206

MODULE

206

PROCESSOR
MODULE

PFT

L

I

N

E

S

5

6

MODULE

206
MODULE

206

Power
Jack

On/Off
Switch

PA

RT

NE

R P

lus

5-Slot Carrier

Summary of Contents for PARTNER Voice Messaging PC Card Release 2




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands